Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Do I need new axles for my modifications?

Join Wrangler Forum Today


Thread: Do I need new axles for my modifications? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-06-2010 09:22 PM
LovethisTJ I think I wanna do the 1 inch BL for now, then when these tires wear down I'm gonna add the 3.5/4 inch lift and 33s at the same time. I think this sounds like a good starting place, like I said I have only had it for about 2 months now and have done nothing except minor mods on the interior to this jeep. So I will keep my decisions updated, and thanks for all of yalls input, it's amazing what just being a part of an online jeep community can do for you.
10-06-2010 06:48 PM
G54
Quote:
Originally Posted by LovethisTJ View Post
He said I should get a 3" BL because he can make modifications to hide the showing of the framework and that if I wanted to do the 3.5-4" suspension lift later I could with no problems..
NO!!! Do NOT get a 3" BL!

Quote:
Originally Posted by LovethisTJ View Post
I just don't know how 7" of lift would look with 33" tires.. at the moment I have a 2" spacer suspension lift and 31s
Okay - here's what I think you should do. Keep the 2" budget boost and add a JKS 1.25" BL and 1" MML (motor mount lift) That will be fine with 33s. Go wheel it. You will soon realize your need for armor and a winch - and maybe if you break an axleshaft - chromoly shafts. Spend your money there first. Later if you want bigger tires there are many ways you could build your Jeep. Higher lifts or low center of gravity (LCG) builds which have become more popular lately. But if it's your daily driver I think 33s are as big as you may want to go.

To give you an idea - here's me on a pretty challenging rocky section of trail - running 33s on roughly 2" of lift and a 1.25" BL - front and rear TruTrac limited slip diffs - and the lifesaver here was my engine skid, control arm skids, rocker guards, and gas tank skid - which I dented and have since upgraded to 3/16" steel.

10-06-2010 04:46 PM
TXRIDER WOW im confused are we doing 33s, 35s, 36s. according to my wife my opinions don't count for much but I think a lot of the questions have to do with what the jeep will be used for and what kind of budget are we looking at.. if that's endless danatrack Dana 60s and and an ls1 for me please
10-06-2010 04:45 PM
cavediverjc Run away as fast as you can from any shop trying to convince you that a 3" BL is the way to go. They don't know Jeeps well enough evidently.
10-06-2010 04:25 PM
LovethisTJ Yeah I'm new to this stuff but everyone starts somewhere right? I've been a Jeep owner for two months, give me a break.. anyways.. I went to a shop today, the mechanic said I should be fine with the axles I have with 33s. He said I should get a 3" BL because he can make modifications to hide the showing of the framework and that if I wanted to do the 3.5-4" suspension lift later I could with no problems.. I just don't know how 7" of lift would look with 33" tires.. at the moment I have a 2" spacer suspension lift and 31s
10-06-2010 10:26 AM
bushy99 yo, you should be fine if you do like a 4 or 5 inch lift with 33 inch tires. thats what i got and i have the d35 rearend. ive done some serious shit with mine and so far no brakage. the black diamond suspension is really good offroad by the way, just on the highway you can feel every little pebble. and its hell on a gravel road.
10-06-2010 09:33 AM
Neil F. To the OP, you are a bit all over the place.

- How are you going to use your Jeep? Are you really using it off-road (and to what extent) or is this more for street and looks?

- What is you budget and how much work can/are you going to do yourself?

- Now that you are down from 36/35" tires to 33's, to fit 33's you do not need that big a lift. 2-2.5 spring lift + 1.25" BL is all you need. (on the street, you can get by with less)
10-06-2010 08:00 AM
cavediverjc
Quote:
Originally Posted by LovethisTJ View Post
Also, would I need an SYE and driveshaft for a 4 inch kit and 33s? Would my stock axles be fine as well?
To do it right, yes.
10-06-2010 07:59 AM
cavediverjc
Quote:
Originally Posted by burton160w View Post
It depends, if you're willing to put the time and effort into it, a Ford 8.8 is a heck of a lot cheaper. If you're willing to research and learn from the 3 million guides about 8.8 gearing and weak points, then you'll spend less on a better axle. At 4 inches, you don't usually NEED one, but your drive shaft will be sitting at a bad angle and should be addressed.

I'm going the Ford 8.8 route, and I spent $200 for a axle with 4.10 gearing and a LSD from a member on here. $425 for the entire installation kit. $100 to have it welded. $100 for the brake rebuild. The rest of the work is being performed by myself and a friend who knows gearing. I'm leaving it at 4.10 with 33s for the time being, but eventually I'll be setting up to 4.88.

For a setup Dana 44, you'll spend at least $500 more and it's a weaker axle.
I assumed that since he was asking so many newbie questions (no offense, OP) that he would have to pay for the 8.8, pay to have the Ford suspension mounts shaved, pay for a TJ mount kit, pay to have someone weld the mounts to the axle, pay for gears, pay to have someone install those gears, pay to have someone install the complete rearend, etc.....that's why I said that in the end, it would cost about the same as a D44. You and I know we can do it A LOT cheaper than a D44, but I'm assuming he can't.
10-06-2010 06:13 AM
SurfNaked2010 if you wanna do it right the first time than this is this is your best bet

Its the RE 3.5" Super-flex kit (with the upper arms also to adjust your pinion angles after the sye install), w/sye and driveshaft, and shocks all as one big kit. people have given 95% great reviews about this kit. its everything you need + more.

Rubicon Express RE7000-3 3.5 Super-Flex Kit & SYE Combo and Shoc

every jeep is different some need a sye at 3" lift some can get away with it until 5" with a TC drop and MML it all depends on the jeep.

and just like burton said above me go for an 8.8 if ya have the cash after the lift, sye, and tires. if not the d35 will hold up just fine with 33's only if you dont lock the d35.
10-05-2010 11:22 PM
burton160w
Quote:
An 8.8 swap would cost ABOUT the same as a D44 once you've purchased it and had the new mounts welded to it.
It depends, if you're willing to put the time and effort into it, a Ford 8.8 is a heck of a lot cheaper. If you're willing to research and learn from the 3 million guides about 8.8 gearing and weak points, then you'll spend less on a better axle. At 4 inches, you don't usually NEED one, but your drive shaft will be sitting at a bad angle and should be addressed.

I'm going the Ford 8.8 route, and I spent $200 for a axle with 4.10 gearing and a LSD from a member on here. $425 for the entire installation kit. $100 to have it welded. $100 for the brake rebuild. The rest of the work is being performed by myself and a friend who knows gearing. I'm leaving it at 4.10 with 33s for the time being, but eventually I'll be setting up to 4.88.

For a setup Dana 44, you'll spend at least $500 more and it's a weaker axle.
10-05-2010 11:13 PM
LovethisTJ Also, would I need an SYE and driveshaft for a 4 inch kit and 33s? Would my stock axles be fine as well?
10-05-2010 11:10 PM
LovethisTJ Is that in quadratec? And that sounds reasonable.
10-05-2010 11:05 PM
SurfNaked2010 6" of lift with 33s!??! go for the Rubicon Express 3.5" superflex kit (its actually 4-4.5") lift with 33's with ease and if you wanna fit 35's down the road get a JKS 1.25" body and you'll be fine.

RE7003 - TJ/LJ 3.5" SUPER-FLEX SYSTEM - Rubicon Express
10-05-2010 10:35 PM
LovethisTJ I was thinking Black Diamond's kit is the one that appealed to me the most. Just the basic 6" lift from them. However, seeing all of this stuff I need to install with the lift kit and tires, it may be over my budget. I might need to reconsider and try to go with a 4 or 5" lift with 33s and a 1" body lift. If I used a 5" kit with a 1" body lift and 33 inch tires, I wouldn't need to swap out my axles would I?
10-05-2010 09:52 PM
SurfNaked2010 new tie rod
drag link
gears front and rear
Labor for gear install about $700-$900
New Brake pads all around
new rims cant use ur stock ones (unless u get spacers)
if ur getting all 5 tires...new rear bumper w/tire carrier

what 6" kit are you going with?
10-05-2010 09:40 PM
LovethisTJ so I should basically just go to a local 4x4 shop and ask them? everything needed for this conversion is: D44 or ford 8.8 in rear, D30 from an XJ or D44 in front, 6" lift kit, 1" body lift kit, 5 35" tires, SYE, Driveshaft... am I missing anything?
10-05-2010 09:21 PM
cavediverjc You could get by with front and rear D44s from a Rubicon.....IF you can find them. Another option is to do a Ford 8.8 rear swap from a late model Ford Explorer. You don't need a D60 for 36" tires. A D60 typically has a HUGE pumpkin, necessitating BIG tires to gain ground clearance. An 8.8 swap would cost ABOUT the same as a D44 once you've purchased it and had the new mounts welded to it. It's NOT a direct bolt-in, but they're in EVERY junkyard out there and they're stronger than the average D44. Any good 4x4 shop has probably done a bunch of 8.8 swaps, so they'd be able to quote you a price. As for a frontend, you COULD probably get by with a later model HP D30 from a Jeep Cherokee (XJ). They run reverse-cut gears and are reportedly about 35% stonger than our TJ LP D30s. Just some more options for you. Currie, Solid, Genuine Gear, and others sell ready-to-install diffs as well.
10-05-2010 09:21 PM
4Jeepn Okay, 1st a few questions, why do ya want 36 tires? what kind of wheeling do you do? As for custom axles you could spend thousands.
10-05-2010 09:15 PM
LovethisTJ so I would need a D44 front and D60 rear for 35" tires and a 6" suspension lift and a 1" body lift? how much would these axles cost me? I've already got the other stuff I need except the axles
10-05-2010 09:11 PM
cavediverjc You've got a Dana 35 rear. You're going to want new axles if you're going to be running 35 or 36 inch tires. If it's going to be a mall crawler, you MIGHT be able to get by, but if you plan on using this Jeep and not being a poser, you're going to want a better rearend. And I wouldn't run 36" tires on the front, even with a chromoly axle kit. So you're probably going to want a new frontend as well.
10-05-2010 09:04 PM
LovethisTJ Here are a few pics of my rear axle. see what you guys can make out of it.. I have no idea which axle this is
10-05-2010 04:58 PM
G54 You have a D30 front for sure. If the rear looks like the pic, you have a D35 rear. If it has a different shape and a metal fill plug instead of rubber, you have a D44 rear. Also in the pic inset you can see where it is stamped "35".
10-05-2010 04:52 PM
LovethisTJ How can I find out what axles I have on there right now? And thanks for the replies and helpful input.
10-05-2010 04:26 PM
edmond You do not NEED them but you will want them. The D35 rear is a major weak point. I think you can keep the front and upgrade as stated above, but the rear should be a D44...however, if you will only be doing fire roads and street driving, you may be able to make the rear axle last a little while, it all depends how you drive. I have seen a D35 break with only 32 inch tires.
10-05-2010 04:21 PM
G54 Assuming you have a D30 front and D35 rear - If you put cromoly axleshafts in your front D30 it might survive with 35s or 36s - depending on how you drive. However if you have the D35 rear it will be a ticking time bomb with tires that big - even with a super 35 kit I would think. Lockers will make it even more vulnerable to grenading. Some will say it is do-able, but most would advise you to at least upgrade the rear to a D44 with cromoly shafts. Ideally with 36" tires, front D44 and rear D60 would be the choice I would go for. If money permitted.

Oh - and you will also need bigger brakes.

Oh - and upgraded HD steering.

And probably some other things I'll think of later.
10-05-2010 03:53 PM
LovethisTJ
Do I need new axles for my modifications?

I have a 2 inch spacer suspension lift kit on and I want to take those out to put a 6 inch long arm kit in, I will also be adding a 1 inch body lift and 36" tires... Will I need new axles? I know I need an SYE and driveshaft but not sure about the axles. I'm running a 4.0l '98 sport edition wrangler and have stock axles. If I need new axles with 36s can I just go with 35s to prevent having to buy new axles? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:03 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC