|03-21-2014 11:15 AM|
|03-19-2014 09:17 AM|
|erazer72||amazing build.... just curious, how tall is your jeep now at its highest point?|
|03-18-2014 08:59 PM|
|03-18-2014 07:16 PM|
|jayru234||Love the build I was considering these wheels for my jeep but was concerned with how far our the wheels stick out can you provide a pick showing how flush the tires sit with fenders...thanks|
|03-04-2014 12:00 AM|
|03-02-2014 09:05 PM|
|Sucker Punch||Looks awesome Rubiwho! I know I have talked to you about the AEV lift before on another thread, but are you still happy with the 3.5 lift with the 37's or do you wish you had gone with the 4.5"?|
|02-19-2014 09:10 PM|
|02-07-2014 04:56 PM|
|kappaknight||I agree, great build! Where abouts in Atlanta do you drive around?|
|02-04-2014 06:57 PM|
|Segfault||Necro your build... just had to popin and say this looks fantastic! I love my Anvil.|
|01-25-2014 04:45 PM|
I just installed the aFe MagnumFORCE Stage-2 PRO 5R Intake Systems, 54-12092-1. Very easy to install, took about 20 minutes. When I first installed the exhaust I didn't notice any performance increase other than having a heavier foot because I enjoy listening to the exhaust note, lol. My gas mileage went from about 15 mpg to about 13 mpg after the install of just the exhaust. I felt like it struggling to get more air... Well of course it was.
After my first drive with the new air intake, I could immediately tell these were meant to go together. High insight I should have done the intake before the exhaust or done them at the same time. I'm hoping to get the 2 mpg back, but then again it sounds really good with intake now. It will be a few tanks of gas before I can get an accurate reading on the fuel flow. I'll post my results when I get them.
|01-24-2014 07:06 PM|
I'm doing the aFe intake tomorrow, so I'm curious how it will change the performance. With just the exhaust I don't really see any performance improvement other than the better sound.
|01-24-2014 12:08 AM|
The aFe MACHForce XP 2.5" SS-409 Model 49-46212 exhaust looks great (what you can see of it) tucked up and out of the way.
Any drone at all?
|01-23-2014 07:21 PM|
|Lionking_FL||Nice man. That looks awesome..|
|01-04-2014 11:42 AM|
|01-03-2014 04:59 PM|
|Sahara Trav||Awesome build. I really like that anvil color and your set up. Where you able to do the bumper & light install by yourself or does it take a few ppl to fit and wire everything?|
|01-03-2014 04:36 PM|
To the OP, your rig looks real nice. Did your homework on this build and it shows.
|01-03-2014 01:09 PM|
|Tyler21||I love this build. The wheel/tire setup is very unique looking in my opinion.|
|12-12-2013 07:53 PM|
|Rubiwho||Rubiwho in her element...|
|12-06-2013 12:56 PM|
Link you the Youtube Sound Clip I made.
|12-06-2013 11:01 AM|
Here are a couple more side shots of the before and after. aFe MACHForce XP 2.5" SS-409 sits up nice. Model 49-46212 for the 4dr
Attachment 569482Attachment 569466
|12-06-2013 10:57 AM|
|Rubiwho||aFe Power 2.5" High Tuck Exhaust installed. Before and after pics|
|12-06-2013 10:53 AM|
EVO Full Protek Skid installed. I am running the AEV drop brackets for the front control arms. So the skid didn't line up perfectly. Since steel does bend... Ouch... I was able to make it work. Also for those running exhaust spacers and want to leave them on you may consider only getting the oil pan and transmission skid and opting out of the exhaust skid because they won't work together.
If you have a manual you'll need to get 2 bolts for the frame mount. After a few stops at ACE, Home Depot, and NAPA, they are 12mm with a 1.5 pitch.
|12-03-2013 07:58 PM|
|Rubiwho||EVO oil pan guard installed.|
|11-20-2013 10:32 PM|
|TJK8||Nice...Anvil, Rubicon, and Rock Monsters...nuf said!|
|11-20-2013 10:02 PM|
RCV axles up front
G2 Gold Chromoly Axles in the rear
Front and Rear Tom Woods 1310 Drive Shafts
|11-08-2013 09:48 AM|
|AudiSportB5S4||Looks real aggressive, love it. Great pic too of the tire of yours up on another, lol.|
|11-06-2013 07:13 AM|
Bumpers and sliders +400
Diff covers, lights, accessories +100
|11-06-2013 03:38 AM|
|chcg12||Nice!! curious about the overall weight? Do you have a breakdown? ie front bumper- 100 lbs,rails -50 bs each etc..? Gave me some nice ideas. Congrats.|
|11-06-2013 03:15 AM|
|clull05rubi||Its easy to cut those flares on a nice warm day with a razor blade. Even a blow dryer or heat gun can help if its not warm any more|
|11-05-2013 08:12 AM|
|Rubiwho||More result... No rubbing in the wheel wells at full flex, up on 37"s, or on the trail. Slight touch of the frame at full steer with the back inside front tires.|
|This thread has more than 30 replies. Click here to review the whole thread.|