Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > considering front and rear receiver hitches for winch

Join Wrangler Forum Today

Thread: considering front and rear receiver hitches for winch Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-16-2014 08:54 PM
thanks to all.. I have more to think about now..

I guess if the weights saving is minimal, there is no reason to go smaller than optimum size.
I had not thought it through, thanks for pointing out it becomes a missile in a crash if not really tightly fixed down.
I am thinking now that the way to go is to just run my solenoids up under the hood and cover the winch and line when not in use.
I appreciate the input.. I guess I just need to get on with it..
02-14-2014 11:08 PM
Majnoon That front receiver Digger has looks a bit weaker than my winch mount but a hell of a lot stronger than a winch cable so if you consider the cable a fuse that mount is going no where.
02-14-2014 09:18 PM
Digger84 Ok but the aftermarket front bumper is quarter inch thick channel and the angle iron behind it is also 1/4 inch thick and between the two they are mounted to every frame bolt that the commonly sold winch plates bolt to so although I don't think the winch plates are the strongest setup out there I don't think the receiver mount is significantly weaker

Then agin I just use it for a rack mount but I would not be afraid to use it as a attachment point for a recovery strap if the need arose
02-14-2014 09:03 PM
Jerry Bransford Knowing what's underneath the bumper where that receiver hitch is mounted, just a steel tube, it's not frame mounted which means it doesn't really have a 5k lb. rating... bad news where any forces could be concentrated into such a small area. I'd bet it could be ripped off with any serious force against its bolts. At best it might be screwed into the tube underneath the bumper that an Antirock uses.

02-14-2014 07:21 PM

This one is 5000 lb

If properly attached not sure winch mount plates are much stronger but still not an optimal way to mount a winch

Not what I use it for but it does fit nicely
02-14-2014 06:49 PM
Jerry Bransford I have always strongly believed a receiver hitch mounted winch is only suitable for light duty winching. Receiver hitches suitable for Jeeps are typically only rated to 3500 lbs. which isn't much when doing heavier offroad winching tasks with a Jeep-size winch typically rated 8000 to 9500 lbs.

I personally wouldn't do it.
02-14-2014 05:09 PM
LJ Dave Don't drive around with something like that inside your Jeep unless you have a way to secure it really we'll. it could kill you in a crash.
02-14-2014 01:30 PM
Shark_13 Purposefully buying a smaller winch then trying to make up for it using block and tackle does not seem like a smart idea.
Weight savings will be minimal, and if something fails someone can be injured or killed, not a good idea to skimp.
02-14-2014 07:29 AM
Digger84 No adverse effect on approach angle if you mount the receiver on top of front bumper

Harbor freight has a heavy duty one with a flat plate and four bolt holes ( they also have a less desirable medium duty one)

I mounted one so I could use front and rear receiver mounted pickup bed extenders (reversed like tall goal posts) to support a long ladder above the hardtop and carry 16 foot synthetic deck planks on the ladder 6 miles home from the hardware store

I did add a piece of angle steel behind the bumper bolted to frame rails so I had a nice wide platform for the receiver hitch plate
02-14-2014 05:07 AM
Big Cole Attaching your winch to a front receiver hitch will negatively impact your approach angles. A quality winch will be able to survive in the elements and there is no reason to keep it stored in your garage.
02-14-2014 01:59 AM
considering front and rear receiver hitches for winch

I would really like to be able to move a winch front to back and detach for placing it inside the jeep or in the garage to keep it from the weather. I am strongly considering the dyneema or other synthetic line for safety and for weight savings, especially if I lug the thing in and out/front to back, as needed. I am considering looking into a winch that will not be as heavy as other choices due to the synthetic line, and overall design and materials... and to save weight and money I am considering getting a smaller winch with less than the reccomended power to jeep weight ratio, and making it up some with a block and tackle, etc. to increase pulling power..
what do you guys think ? I know it is a lot of questions.. but seems we need them asked together to better get the best answers possible.
thanks in advance:
dan kennison

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 05:02 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC