Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > same old alignment question TOE IN

Join Wrangler Forum Today


Thread: same old alignment question TOE IN Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-19-2010 01:24 PM
rrich It's going to be somewhat dependent of the wear on your suspension. As the tire rolls there is pressure from the street trying to push them apart - to toed out.
Setting it slightly toed-in to start with compensates for that pressure - eventually equalizing to a straight ahead position - when they just roll without scuffing. (Scuffing is actually removing rubber!)

The more everything is worn, the more it toes out when driving.
If the suspension is new, set it to slightly less toe-in.

The real proof is in the results.

Keep an eye on the tires and how they wear. After 500 miles or so - Lay your hand flat across the tread. You can "feel" how it's doing. You can feel if one side of the tread is wearing more than the other. That's camber - not easy to correct on a Jeep.

After you feel the crown, drag your hand back and forth across the tread. Notice the grooves - the edges in particular. If the inside edges of the grooves feel like sharp corners and the outside edges feel more rounded, then it has too much toe-in. The tire is sliding sideways slightly on the road (scuffing,) causing inside of the groove's edge to feather a little, the other side will feel slightly rounded.
If it is actually making a feather edge it's waaay off! Both sides of the groove should be about equal.

Notice how an experienced alignment guy looks at it - he "looks" then "feels" before he tells you what's needed. It's all right there if you know how to "read" it.
10-19-2010 11:52 AM
Jerry Bransford Typically, the usual recommended toe-in is 1/16" to 1/8" and 1/4" is way too much. The bigger the tire's diameter, the less toe-in that is desireable so 1/32 is not out of line.

The two below pics show a very good way to measure your toe-in more accurately (and repeatedly) measure your toe-in than is typically obtained when just measuring between the tires.

It requires nothing more than a pair of 1" square aluminumum tubes and spring clamps. Mark the tubing at points equal to your tire diameter and measure between the sides at those marks.
10-19-2010 11:10 AM
mrcarcrazy 1/32 total toe is going to be fine. I wouldn't expect any issues arising out of this setting. The thing about OEM specs is they are for OEM suspensions. Yours is not. lessening the Total toe will lessen the wear caused by toe angles on your wider than stock tires. If it drives fine It will be better off IMO

If you have wiggle when you shake the tires, you need to be replacing components. There should not be play in front end/steering parts.

I used to do this for a living. But as always YMMV.
10-19-2010 10:59 AM
jgorm IMO any of those are decent for the jeep on 35s. Lift the jeep up and wiggle the tires back and forth. I bet that they move more than a 1/8" at the front of the tire.
10-18-2010 10:28 PM
Ray - San Jose I took the info from the factory service manual and calculated it out to be 5/32" at 30" as being optimum spec, according to the factory numbers. So I'd say 1/32 isn't enough.
10-18-2010 09:43 PM
cheap jjep
same old alignment question TOE IN

wasted money paying someone else to do an alignment instead of me and a tape measure. i have read everyone says toe in should be about an 1/8 to a 1/4. mine was a quarter (set by me) and the shop changed it to 1/32. Is this to little. I am running 35"bfg's.
on a side note.... this forum has been the biggiest money saver of all. I think i have already paid for my computer with all the money saving advise found here. THANKS ALWAYS!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:37 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC