|05-07-2011 10:59 PM|
|05-07-2011 10:56 PM|
|05-07-2011 10:19 AM|
|jeepjones||The "clunk" could possibly be the transmission mount on the skid plate is worn or damaged and everytime you start or stop the trans is moving on the mount which can be felt and heard.|
|05-07-2011 03:24 AM|
|Jollyczar||Beer30, is it a single "clunk" that you can feel through your floorboard when starting from a stop within the 1st 10mph or so?|
|05-07-2011 02:32 AM|
|cromulent||I will be changing my ujoints this weekend so hopefully it is as easy as people say it is. definitely better than taking it to a shop|
|11-14-2010 03:20 PM|
Thanks for the tip. I'll try that first. I don't have the "angry sparrows" or anything, just a clunking noise, but that happened in a truck I had and it ended up being the u-joints so that is what is leading me to suspect them.
|11-14-2010 01:44 PM|
|rrich||I'd think trying to change the axle U-joints without removing the axle would be about as difficult as doing a valve job through the tailpipe or heart bypass surgery through the rectum.|
|11-14-2010 11:19 AM|
|Jerry Bransford||Remove the front driveshaft or at least disconnect it at the front and zip-tie it up out of the way and test drive it first to see if the clunk goes away. No need replacing the driveshaft u-joints if they aren't the problem either. Good choice on the Spicer 5-785x u-joints for the driveshaft.|
|11-14-2010 10:06 AM|
Thanks again for the tips everyone. Mission accomplished. Wasn't too bad of a job at all. One of the u-joints was bad, so I guess it's a good thing I did them because I would've had to eventually anyways.
Unfortunately, it did not solve this clunking noise that I keep hearing. Now I'm wondering if it is driveshaft u-joints. It only seems to happen at low speeds and just sounds like a clunk coming from underneath (I thought it was the front at first, that's why I started there). There's no rhythm to it, and it doesn't seem to do it consistently. I already have a set of 5-785x's for the drive shaft anyways, might as well put them in and see what happens. Anyone have any other theories?
|11-13-2010 01:03 PM|
Here's a couple more helpful writeups:
U-joint replacement - Hammer method
Driveshaft rebuild - Press method
It really is pretty easy. The most difficult part is keeping all those needle bearings where they need to be.
|11-13-2010 12:34 PM|
|HyperBuzzin||I went with the Alloy USA U-joints. Greasable thru each of the end caps, so no crossed drilled holes to weaken them.|
|11-13-2010 12:33 PM|
Thanks for the write ups!
The hub/bearing assembly came off nice and easy using a section of 2x4 between the inside face of the rotor and the frame underneath where the shock mounts and turning the wheel. Hardly needed any pressure at all, they came right off.
Now for the u-joints themselves....
|11-13-2010 11:56 AM|
First, I hope the Spicer u-joints were their 5-760x which is a nice stronger and more durable upgrade from the factory installed Spicer 5-297 u-joints. Plus the 5-760x is sealed so it is stronger since it hasn't been cross-drilled for grease channels.
Here are a few webpages from Stu's site that may help...
D-30 Axle Shaft Removal
Unit Bearing - 1
U-Joint Replacement - 1
|11-13-2010 11:50 AM|
Working on this today. Any tips for removing the hub/bearing assembly?
Yes, I removed the three bolts and the axle nut. It's not all that rusted either. Do I just have to hit it pretty hard or is there some other trick to it?
Edit: I found a trick in this thread. Hopefully that'll work!
P.S.- Does anyone know why we can't search for three letter words? That's really annoying.
|11-04-2010 12:22 PM|
Agreed, you could try but you're going to over complicate the job by leaving the axle shafts in.
There's not a whole lot of room in there and you'll be working around other stuff that gets in your way: tie rod, ABS sensor wire, the steering knuckle itself... To do it with the axle shafts still in you would have to jack up the front axle anyway so you could turn the axle shafts to get to all 4 of the caps, and then installing the new u-joints would be a jockying nightmare getting them started and pressed straight and then you still have the retaining clips to get in too; which are not on the outside like drive shaft u-joints. At that point it's a whole lot easier to just pull the shafts.
I've pulled my front shafts enough to where I can do it pretty quick.
|11-04-2010 12:21 PM|
The time I waste trying to press them out with the axles still in, I can probably save by pulling them out and using a vice.
|11-04-2010 12:10 PM|
|DevilDogDoc||You can try but it's hard to press them out still on the Jeep. Real easy to pull front shafts.|
|11-04-2010 12:06 PM|
Front axle u-joint removal
Need to replace my front axle u-joints (I think). I actually found a place somewhat local that carries Spicers, so I'm going to fetch a pair this afternoon.
The Service Manual says to remove the axle shafts. Has anyone actually had to do that or were you able to get the u-joints out with the axle shafts still in?
Any other gotchas I should be aware of? This will be my first time doing axle u-joints.