Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Beefed the rear driveshaft up

Join Wrangler Forum Today


Thread: Beefed the rear driveshaft up Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-09-2010 10:42 AM
Jerry Bransford
Quote:
Originally Posted by KeeblerKO View Post
Jerry.....? Is that blood splatter by the e-brake cable?? Running over zombies?
That's red grease from greasing the u-joints. Yeah it makes a mess on the underside since I don't try all that hard to get all the excess grease off. I wipe it off best I can but there's always enough to sling out while driving. Personally, I don't like or use greasable u-joints, the previous owner had that driveshaft built which included greasable u-joints. Only if I did a lot of deep mud would I want greasable u-joints. I mean, heck, look what it did to my muffler.

Quote:
Originally Posted by EdJonesJeeper View Post
That looks like grease from a well maintained non-sealed u-joint in the original shaft. You can tell Jerry's deff. doing his maintance rituals. hehe

Hey jerry, how did you get into the ujoints to grease them withough having to take the shaft out (for those of us who didn't get sealed u-joints), and with the TW shaft what did you replace the output yoke with at the t-case?
I've had two driveshafts with greasable u-joints Ed and you just can't get to all four zerks without at least unbolting it from one end. I usually removed the entire driveshaft to make it easier to grease properly, and so I could also move the CV and rear u-joint around to feel for any wear problems. I discovered a bad CV I didn't know I had that way a few years ago. I had to replace the t-case output yoke with a flange which Tom provided to match the 1350 size CV.

One more nice thing about the new DS with sealed u-joints... 3 less zerks to grease!
11-08-2010 09:27 PM
Elwood I assume Jerry knows, but for anyone else taking the balancer off the back of a Rubi transfer case, make sure your speed tone ring stays in place and the little pin behind it stays put. If it comes out and gets put back in wrong, it can cause run out that causes vibrations.

I chased this for a long time on my last Rubi. Here are pictures from someone else that I found online.

http://www.thedragonsden.net/jeep/241/
11-08-2010 07:59 PM
KeeblerKO
Quote:
Originally Posted by EdJonesJeeper View Post
That looks like grease from a well maintained non-sealed u-joint in the original shaft.
That's what they tried to tell me about Roswell. I know zombie brain matter when I see it!

**whispers**What's going on in California...?
11-08-2010 06:22 PM
EdJonesJeeper
Quote:
Originally Posted by KeeblerKO View Post
Jerry.....? Is that blood splatter by the e-brake cable?? Running over zombies?
That looks like grease from a well maintained non-sealed u-joint in the original shaft. You can tell Jerry's deff. doing his maintance rituals. hehe

Hey jerry, how did you get into the ujoints to grease them withough having to take the shaft out (for those of us who didn't get sealed u-joints), and with the TW shaft what did you replace the output yoke with at the t-case?
11-08-2010 06:00 PM
neverfastenough1
Quote:
Originally Posted by Jeepzcb09 View Post
Hows the nail file gonna help
Its a known fact that the "pink" nail files are made from one of the strongest substances found, and they have great flexability. However, I do think he chose the wrong tape to hold it all together.
11-08-2010 05:22 PM
KeeblerKO Jerry.....? Is that blood splatter by the e-brake cable?? Running over zombies?
11-08-2010 05:21 PM
Jeepzcb09 Hows the nail file gonna help
11-08-2010 05:20 PM
village idiot Really good info, Jerry. Coincidentally, I am going to be installing my Rokmen belly-up skid just as soon as it comes off back order (supposed to be this month), and I've been thinking about what to install for a new drive shaft. I think I know now. Be sure to keep us posted if any issues crop up, but it looks bullet proof, particularly the side by side pics.
11-08-2010 05:15 PM
Cons_Table
Quote:
Originally Posted by bobjenkins View Post
Funny that you started this thread. I just finished reinforcing my rear DS. rock solid baby. lets hope I have a catastrophic DS failure this weekend and get to test the tensile strength of that pink nail file
Tom Woods has nothin on that
11-08-2010 05:08 PM
bobjenkins Funny that you started this thread. I just finished reinforcing my rear DS. rock solid baby. lets hope I have a catastrophic DS failure this weekend and get to test the tensile strength of that pink nail file
11-08-2010 04:53 PM
Cons_Table That thing is a beast compared to stock
11-07-2010 06:57 PM
jdhallissey Looks great. I wish he would of built mine like that the second time when I blew mine up after only having it in the truck for 8 months.
11-07-2010 06:50 PM
Jerry Bransford
Beefed the rear driveshaft up

The aftermarket rear CV driveshaft in my Rubicon started making some noise recently that didn't sound good. After determining its u-joints and CV joint all seemed ok, I figured out that it was caused by the extra steep angle at the CV caused by the recent installation of a used belly-up skidplate. The bellyup raised the t-case approx. 2.5" which is when the drivetrain started getting noisy from the steeper angle at the CV. The angle at the CV didn't look all that steep but the existing driveshaft apparently didn't like it.

I emailed driveshaft guru Tom Wood for his advice and he immediately replied with his well-known outstanding support. The first of two options Tom presented involved a pure 1330-based CV driveshaft with 1330's at both ends. The second option having a 1330 at the rear and two larger 1350 u-joints in the CV, a beefier CV joint, and a new front flange mount. The new front flange also created a bit more room so the driveshaft could be a tad longer which helps with the angles. I couldn't resist the stronger option so I went with Tom's "hardcore" 1350 version. I also requested Tom build it with all sealed u-joints which he readily agreed to.

The new driveshaft arrived and I immediately noticed how much heavier it was even before excitedly opening the box.




When compared to my old 1330 driveshaft side-by-side, the awesomeness of the new 1350/1330 driveshaft is readily apparent.



Weight-wise, the new driveshaft was nearly 25% heavier at 20.6 lbs. vs 16.0 lbs.. The larger CV and larger DS diameter is responsible for that.

All in all, I'm pretty stoked to have a Tom Wood driveshaft again now that I have replaced my stolen '97 TJ with the '04 Rubicon Jeep... especially that it looks pretty bombproof. The last time I wheeled my '97 TJ with its 1310 based rear CV driveshaft, I managed to break it at its yoke and rear u-joint. Because of the way things broke, which also went beyond just the driveshaft with a ripped off control arm mount, broken control arm bolt and a broken wheel, I had to make one driveshaft out of two bad ones to get home the next day.

Here's the new shaft installled...


The old shaft...


So now the old DS has become a spare for the unlikely event I manage to break this one... which sure doesn't seem very likely. Thanks Tom, I am stoked with the new DS and just how fast you got it to me!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:11 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC