Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > bone stock rubicon 44 front axle noise

Join Wrangler Forum Today


Thread: bone stock rubicon 44 front axle noise Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-14-2010 01:28 PM
rubiconSean hey whats the way to go about fixin this thing
11-12-2010 07:29 PM
rubiconSean hey! thanx for getting back to me on that thread, The ball joints are ok so far, i popped those in around 90k as well as the wheel bearings, right front wheel bearing has some play but i think i may have had something to do with that when I extracted it (with a large hammer, damn natural occuring salt water indiginous to New Jersey) to remove my axles only to bolt in old stub shafts and pop the ol rubber freeze plugs in the tubes, little trick i came up with when i killed an inner shaft and had no dough for a new one. Thanks for the suggestions UnlimitedLJ!

Keebler.. Ive been looking for That pic just about everywhere thanx. As for the tech info, the retaining pin just slides in and out of the carrier/cross shaft. what would you recommend for the fix, should I attempt to tap it back into place or should i look into replacing the cross shaft and retaining pin. Also is this a relatively common problem for this diff? the spiders look ok so far but if im doing a cross shaft i may as well replace the cross shaft. meantime so i can drive it like i said earlier Ive popped out my axles n front drive shaft bolted in some old stub shafts to the hubs and put the rubber freeze plugs in the tubes to avoid catastrophic failure (im sure that carrier or housing aint cheap). Still gotta get back and forth to work and the bar. lol go go gadget 2wd rubicon!
11-08-2010 11:57 PM
KeeblerKO On the Dana 30 the pinion cross shaft is held in with a press fit collar rather than the 1/4" retaining bolt like you find in the rear D35 carrier. It takes a small punch and some good whacks to get it out. It should not be loose, nor should the cross shaft be loose enough to wiggle. Loose enough to push out with firm pressure from your finger once the retainer is out, sure. But it should not wiggle side to side or up and down with the retainer in.

Sounds like it's wiggling and causing your spider gears to not mesh up correctly with the side gears. That's probably what you heard once the gears were forced to mesh back together properly during the turn.

You're only hearing it turning because of the inside wheel during the turn needing to rotate faster than the outside wheel. Even in 2wd. Sort of like how a Lock Right in the front axle will click when turning in 2wd, except you're hearing your spider gears/side gears. Going straight both wheels are rotating at the same speed, so there's no large difference in force being exerted from one side of the diff carrier to the other.

If that cross shaft is wiggling, eventually, at some point, you run the risk of breaking a tooth on one or more spider or side gears if they end up trying to jump a tooth.


Here's a diagram of the front D44
Dana Model 44 Front Axles for Jeep Wrangler TJ at Morris 4x4
11-08-2010 10:19 PM
UnlimitedLJ04 have you checked the ball joints and wheel bearings? wheel bearings usually die around 60k miles...
11-08-2010 08:06 PM
rubiconSean
bone stock rubicon 44 front axle noise

Hello there, I have an 03 tj rubicon, just cracked 118k today had it since new, pulling out of a parking spot in a tight turn i heard/felt a click klack in the front end thought i just ran something over (nothing unusual) till it happened the next turn as well. Crap.. got home. this time it aint the axle joints.. (Ive replaced them several times over the years most recently about 9 months ago) this time its coming from the diff. so i promptly pulled the cover. from what i can see the spiders look ok but they jerk along with that center pin in the carrier.
Now for the question.. that little pin that holds the big pin. thats not supposed to just kinda slide in and out is it? I havent really screwed with air lockers, but every other rear ive worked on that pin is threaded in and has a 5/16 head on it. this pin doesnt look sheared and almost looks as if its a press fit. can anyone enlighten me? 03 tj rubicon factory front dana 44 air locker I cant find a good parts diagram on the interweb. Thanks in advance

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:44 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC