Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Grinding/rubbing noise when clutch is engaged, stops when released

Join Wrangler Forum Today


Thread: Grinding/rubbing noise when clutch is engaged, stops when released Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-19-2010 12:43 AM
MCE Mike I would inspect the clutch while it is apart and go from there. Throw out bearings take a while to go out usually, unless they have been in a lot of water or mud. If the clutch truely was replaced not too long ago (some one didn't lie to you, etc.) then the TO bearing shouldn't go out this early, unless it is somehow a defective unit. The TO bearing should have been replaced with the clutch if it wasn't.
11-18-2010 07:08 PM
Case Would it be a good idea to get a whole new clutch kit?
11-18-2010 07:07 PM
sppfields sorry, i dint read the rest of your post. the reason you can move it freely while bleeding is that the clutch pedal is out and there is no pressure on the throwout bearing. it just sits on the transmisssion input shaft . dont worry, this is very normal. But, trust me you will be changing the throwout bearing.
11-18-2010 07:03 PM
sppfields throw out bearing is correct, with clutch pressed in it makes contact with the pressure plate. with clutch out. it just sits there.
11-18-2010 07:01 PM
Case It's the opposite, it doesnt make the noise unless the clutch is pressed in
11-18-2010 06:48 PM
gryph Throw-out bearing

Depress clutch pedal lightly, noise goes away? release pedal noise comes back?

That's it
11-18-2010 06:32 PM
Case
Grinding/rubbing noise when clutch is engaged, stops when released

I have a 1993 wrangler 4.0. The motor and tranny were just rebuilt very recently. It also has a rebuilt 4:11 rear and had a new clutch. Not long ago I rolled it offroading, but luckily there was no serious damage. I let it sit for a couple days, changed the fluids and everything seemed fine.

A few days later it began to make rubbing/spinning noise when the clutch was engaged, but stopped when it was released. The noise got worse to the point where you could alwyas hear it, but it got worse when the clutch was engaged. I have been told that it sounds like an issue with the throwout bearing, but anything i saw about the throwout bearing said that it made the noise all the time but stops when the clutch is engaged.

Before I got into anything serious i bled it and at first the noise went away but after about 20 min it started again but was much softer. I bled it again, but the noise continued. While bleeding it, I noticed that the bleeder valve and the clutch line next to it moved side to side fairly freely. It is an internal slave, so i couldn't see if it came loose or was supposed to do that. The jeep does shift into all gears smooth and easily.

I was wondering if it was more likely to be the throwout bearing or the slave cylinder, or something else. Any help would be greatly appreciated.

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:35 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC