|11-27-2010 06:48 PM|
|markharmon||The fuel line hose and return hose are 2 different sizes on my 95yj, I had to pull the cluster with spedo and tach all the way out if the dash. Mine has 1 d-shaped connected that feeds the tach the spedo and the idiot lights. Coming off the connected is 2 ribbon cables. I found 4 of the ribbon lines broken. I solder jumper wires and now every thing in the cluster works. Someone else mentioned some metal conductor paint instead of jumper wire. I guess you use it to fix rear defrosters.|
|11-27-2010 02:25 PM|
|MMata77||welcome to the forum|
|11-27-2010 02:21 PM|
Thanks for the tips!! I inherited a lot of things that some previous owners did not fix right. I bought a new switch and it didn't fix the problem. I checked and I'm getting power to the switch. I didn't check where they connect with the cluster. Where is that?
I just bought the hose I needed for the fuel filter and it ended up being two different sizes. Hopefully after these problems are done I can enjoy driving it.
Thanks again for all the input it's been a huge help!
|11-26-2010 08:19 PM|
feel free to call me if you have any questions about your new jeep .
|11-26-2010 07:10 PM|
|sinepome||I had the same prob with lights. Mine ended up being the dimmer switch. I Played with it for a but and it turned on. I just dint mess with it now and it works like a champ.|
|11-26-2010 06:50 PM|
|markharmon||I had similar dash light and gauges didnt work issue Turned out to be corroded wires leading from connector backside to cluster. On the fuel filter I replaced my 95 2.5 liter filter And it uses 2 rubber hoses from stainless line to filter and from filter to stainless line that runs over to tank.|
|11-26-2010 03:54 PM|
|Garyk||On the dash light problem, if you are sure the fuse panel is good and fuses are good, check the connection at the light switch. As far as the gas filter, the connections are with hoses, just make sure to use hose made for fuel lines.......there is some pressure in the line so be prepared..|
|11-24-2010 02:01 PM|
Rusty, leaking fuel filter
Quick question. I need to replace the fuel filter along the frame rail of my 94. It's leaking slightly and rusted pretty bad. I'm picking up the part tonight but I believe it's high pressure line so does that mean I cannot use rubber hose to connect if the line at the fuel filter is bad? If so are there compression fitting for that?
I appreciate the info!!
|11-24-2010 01:42 PM|
Thanks, I checked out the site. Very cool gauges. I was hoping not to have to resort to that yet. None of the interior lights work. Seems like it should be tied to a fuse?? The fuses under the dash are ok. Fuses under the hood look okay, not sure if it could be a relay. I don't have to much trouble fixing mechanical things but electrical problems... I don't have a clue.
Thanks again for the input! I appreciate it.
|11-24-2010 09:52 AM|
|11-24-2010 09:37 AM|
|Rastaman69||Welcome to the forum! Check out the link from fweaky...I've used it before.|
|11-24-2010 07:58 AM|
|11-24-2010 07:48 AM|
|JackdUp||Welcome to the forum. Good luck with the dimmer challenge.|
|11-24-2010 07:23 AM|
|jmac1||Thanks! this is a great forum! I appreciate the help also. I'll check out those gauges.|
|11-24-2010 07:19 AM|
|11-24-2010 06:06 AM|
|JDsDream||Welcome to the Forum|
|11-24-2010 01:43 AM|
Welcome to the forum. I bought a nice dash panel and set of gauges from these guys and they have a diagram of the wiring on their web site.
Custom Instrument Panels | Jeep gauges | Fort Worth, TX
|11-23-2010 09:59 PM|
New guy from Ohio
Hello, I have a 94 wrangler and the instrument panel lights don't work. Some genius cut the wires and removed the dimer switch. I have a new switch but after hooking it up and checking fuses they still don't work. Any idea what to try? Is there a way of knowing if the lights are blown? Thank for any help!