|03-08-2013 08:26 AM|
|jeepers29||Subbed for future use. Thanks|
|03-08-2013 02:21 AM|
|Wheel2Work||Great write up, but won't work for my 2000. After pulling it all apart, I found that the lock cylinder was actually used to move the latch! Just a small tab on the cylinder is making contact with the release, so I either live with it, or replace the lock cylinder entirely…|
|12-01-2010 12:59 PM|
|Wrangler1212||Anyone else try it yet?|
|11-30-2010 03:49 PM|
|11-30-2010 03:39 PM|
|11-30-2010 03:36 PM|
I should add a warning not to shorten the length of the pin, only round off the edges.
Sorry to hear you had a little trouble Bob.
|11-30-2010 03:15 PM|
|bobjenkins||I shaved off too much and out didn't work. But I got it working again|
|11-30-2010 02:22 PM|
|Wrangler1212||Geeeez it's so much easier to get into my console...what a difference.|
|11-30-2010 08:28 AM|
|InfernoGirl||Be aware that getting the spring replaced so that it actually works again can be a challenge..... I thought for sure I had totally screwed mine up, but finally, I got it all put back the right way...... This is why I don't do much installation.... I'm very good at removal, installing is a whole nuther story.....|
|11-29-2010 11:37 PM|
|bobjenkins||I say keep a bag of shit in the center console. If someone wants to take the time to break into it they'll get a nice treat. My valuables go with me or in a lock box. Nevertheless I'm doing this mod|
|11-29-2010 11:28 PM|
|11-29-2010 06:36 PM|
|Wrangler1212||I've heard about these locks failing from a number of jeeperz who have had the same issue. It's a matter of time. It's a simple fix though. Either "Jeep" should go with a metal center pin to avoid warping, OR just have this pin rounded on the manufacturing assembly line huh?|
|11-29-2010 06:24 PM|
|beefmobile||Mines a .50 cal ammo can|
|11-29-2010 06:05 PM|
|11-29-2010 05:56 PM|
|harwa004||This is great info coming along at the perfect moment. Just had to pull my lock out because it was jammed completely. I will try this and get it all fixed! Thanks!!!|
|11-29-2010 04:41 PM|
|bobjenkins||Mine is hardware hell to open when TS unlocked ( unless you know how to do it right. So I figure a theft would come andvthink its locked then leave!|
|11-29-2010 04:37 PM|
|InfernoGirl||I did the same thing for mine, works like a charm. Only thing I did different was instead of using a knife, I filed mine down flat.....|
|11-29-2010 02:01 PM|
Quick fix for your center console lock
I was about to go buy a new lock for my center console because it would stick as if it were locked. It gradually got worse until I couldnt push the lock open anymore on my console. This fix should work for most models and years because the lock is pretty standard. Mine is on a 2003 TJ. The "catching" symptom is caused by the center pin being tooo flat (such as an unsharpened pencil). This fix will round off the center pin allowing it to glide smoothly against the lock plunger.
Here we go:
1st, remove the lock mechanism by pushing in both tabs located on either side of the bottom side of the lock, see pic A. See pic B for mechanism removed.
2nd, now push in the single (1) plastic clip on the side of the mechanism located above my thumb in pic C to remove the lock out of the housing. Do this over a table to catch the pieces that will fall once the lock is removed. there are 4 internal pieces.(2 springs, center pin and the plunger see pic D).
3rd, I've already rounded off the flat side of my center pin (see pic E). Your's will come out flat (like an unsharpened pencil). Shave off the edges of this plastic piece and the plunger will slide easily again as if it were brand new. Put the lock mechanism back together in the reverse order and you should have no problem. You just saved some cash. Good Luck.