Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Discussion Forums > Off-Topic > trailer woes. Axle mod question

Join Wrangler Forum Today


Thread: trailer woes. Axle mod question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-17-2007 01:37 AM
AzTJ I'd just swap them, that would be the easiest way... and since it has no fenders that would have been my only other concern.
06-17-2007 12:50 AM
cecoen HELLO....can you say moron boys and girls! Can't believe I didn't see that. YES, just swapping the axles around will work and should be super easy. Compared to grinding welds anyway. I too wondered why the axles weren't standing straight up but just assumed it was for axle travel up and down or something.

OK, so if I swap axles front to back, see any reason why it should hurt anything? The axles are on seperate leaf springs. So will it matter if they point away from each other a little as opposed to towards each other a litte? I have no fender issues because I was going to install them after the larger wheel/tire install. It has no fenders right now. And I can think of no other rub/fitment issues?

Thanks for the advice,
Chad
06-16-2007 11:51 PM
AzTJ Each axle is on its own leafspring right? What about rotating the leafs around?

I think that angle is there for suspention travle when hitting bumps in the road, acting somwhat like a shackle.
06-16-2007 11:48 PM
jjseel That doesn't make sense to me, being tilted that way. Both of my trailers have the axles centered. Which looks easier, moving the shackle brackets, or moving the axles?
06-16-2007 11:44 PM
cecoen
trailer woes. Axle mod question

Hello all,
Hopefully I can explain this in a way someone will understand it. And hopefully someone will have some advice! I have a light duty car hauler type of triler. It has double dropped axles. It had 14" wheels and tires. I found a sweet deal on a set of Jeep take off wheels and tires that are 15" When I went to install them they rub each other. Front tire rubs the back tire. I really want to run these new tires. I began looking at the axle set up and it seems(see photo) that the dropped axles are clocked a little towards each other thus bringing the two hubs closer together and making the larger tires rub. My first thought was to loosen the u bolts holding the axles to the perches and rotate them a little bringing the hubs a little further apart and making more room for the tires. I then found out that the little cups that the axle sits in on top of the leaf springs are welded to the axle.

I was thinking I would grind the welds off and rotate the axles a little. What do you fab gurus think? I figure that the axles are not straight up and down to compensate for suspension travel but will moving them hurt anything? Am I making any sense? If you look at the pic of the rear axle I tried to show with red lines how pitched forward the axle is and where I want to move it to. Any ideas? Any idea what the heck I am talking about?

THANKS!!!!!
[IMG][/IMG]

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:35 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC