|12-23-2010 05:09 PM|
|Wdkirk01||Put a piece of cardboard in front of your radiator to protect it should you slip with any of your wrenches while taking off the fan blade and such. Hesco.com has some nice Hi-Flo water pumps and thermostat housings if you feel like upgrading. Kind of pricey though.|
|12-23-2010 01:08 PM|
|12-23-2010 09:58 AM|
|TexasT||Before you start...make sure you understand how to loosen and tighten the belt. It is not hard but can be frustrating if you don't understand the tensioner function. Two bolts, 15mm I think, one just locks it in position and the other to loosen and tighten the belt. The tensioner is by the PS pump. Also some thermostats have a small hole on one side. If you get one with the hole it is a drain hole and should always be mounted in the down position. I just replaced mine and it did not have the drain hole in the new one. Also have a supply of band aids...everything sharp hangs around the shroud and fan blade.|
|12-23-2010 08:41 AM|
|TRV-Toyota Rescue Vehicle||Good to know about the fail safe. Sorry about the bad input. Lol! But now that I've heard 1st hand. I think I'll just keep it simple. Thanks!|
|12-23-2010 07:54 AM|
|dan188||You won't have too much trouble putting in the water pump. I did it in about 2 hours in my 98 4.0. There isn't anything too challenging. Basically, you drain the radiator, while taking the radiator shroud off along with the fan, loosen and remove the belt, take the top hose off the T-Stat housing, remove the pump and T-Stat housing once the block is drained enough, use gasket maker along with the new gasket and re-install new parts.... The biggest pain I had was getting the belt back on. I kept putting it on the wrong pulleys. Tools needed were a 15mm for the bolt that tightens the belt, and I think 10mm for the water pump and t-stat bolts, and I don't remember what the fan bolts were, but they were small. Maybe 10mm also.|
|12-23-2010 05:33 AM|
|12-21-2010 10:48 PM|
|98tj25l||Replacing the water pump was my first DIY job, and it really wasn't too bad. Like others have said replace the thermostat, and when I did my job I also replaced the radiator hoses. Not to discredit TRV, I would stay away from the fail safe thermostats. I seem to remember a lot of people having issues with them failing quickly upon installing them. I just bought a standard thermostat and haven't had any problems with it.|
|12-21-2010 10:34 PM|
I would say do it yourself although I would do so only if I had a place out of the snow to do so.
Think it took me around 5hrs but I never do anything easy
|12-21-2010 09:22 PM|
|TRV-Toyota Rescue Vehicle||Take TexasT's advice. Changing the thermostats a mandatory whenever ya gotta change out the water pump. Especially if ya might have gotten hot or your thermostat had to work hard. Try to find a fail safe one (one that stays open when it fails) if your willing to spend the extra money. Haven't done it yet myself, but looking to soon since my thermostat has been workin a little hard with the elec fan conversion I just got done with.|
|12-21-2010 08:47 PM|
|TexasT||It's a pretty easy job just take your time. No special tools required. Good time to change the belt and thermostat too.|
|12-21-2010 01:12 PM|
How long does it take to put one in? and does it require any special tools?
Water pump went on my Jeep and I need to replace it. Guy at the shop wants to charge me 3 hours to put it in. I bet i can do it faster and far cheaper... eh?
1998 Sport, 4.0L I6 (5 speed)
where can i get one and at a good deal....