Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Sway bar disco's

Join Wrangler Forum Today

Thread: Sway bar disco's Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-03-2007 02:11 AM
jherrin215 I don't think they do, I have never seen them. I made my homemade disco's tonight. I used that write up then welded the 7/16 washer to the clevis pin, then welded that washer to the big washer that is on there stock and ground it down and painted it black. Looks like it is gonna hold up good. Also tiny I got those in the mail!! Thanks a lot. I have some ideas to try with those so I will see what I can figure out!!
07-03-2007 12:23 AM
Chad P I know I was just wondering if they make disconnects for the rear?
07-03-2007 12:12 AM
Triple88a Chad i think the rear is soft enough. On my rig the rear always gives in if i don't disconnect the front.
07-02-2007 11:28 PM
Chad P Can you disconnect the rear swat bar for more flex
07-02-2007 04:27 PM
Bluesman I honestly did not run it enough to tell. I got the JKS and only used the home made ones a couple of times, and put very little miles on them.
07-01-2007 02:07 AM
Originally Posted by Bluesman View Post
I used to use these homemade ones. welded a washer on to prevent failure. Now use JKS.
Did you ever have any trouble out of this setup you had on yours??
06-26-2007 02:06 PM
jherrin215 I like the washer idea, I think I may get a grade 8 washer and weld on to mine to prevent them from wearing out if I go with this kind of disconnect. I was trying to figure out a way to disconnect and reconnect them in the center of the link. I will have to see what I can come up with though!
06-26-2007 11:46 AM
Bluesman I used to use these homemade ones. welded a washer on to prevent failure. Now use JKS.
06-26-2007 02:03 AM
jherrin215 I should have jumped on that one that Mr.C had for sale on here!! It was a good buy and would have been nice to have!!
06-25-2007 04:27 PM
Scout AntiRock.
06-25-2007 04:22 PM
Originally Posted by Chad P View Post
I have my stocker as well let me know if you need them cuz I don't heck I have all my stock stuff. Need anything else?
I need driver rear roll bar cover
06-25-2007 03:42 PM
Chad P I have my stocker as well let me know if you need them cuz I don't heck I have all my stock stuff. Need anything else?
06-25-2007 12:39 PM
jherrin215 Wow, thanks everybody!! I was thinking that if I did make them and something broke, it shouldn't be a major catastrophe, just should be a little wavy ride until I could replace it. Oh and tiny, you have a PM!!
06-25-2007 12:39 AM
Originally Posted by nicolas-eric View Post
home made discos:

cost only about 5$
Post Installation Notes
After using this setup for over a year, one of my homemade discos failed while driving on the highway. Although this did not cause me to loose control or significantly change the driving behavior of my Jeep, it is never a good idea to drive at highway speeds with your swaybars disconnected. If you still plan to do this mod, I would strongly advise you to to check the hardware component on a regular basis for wear and replace them as needed.

Disclaimer: The modification detailed above is not recommended by the manufacturer of this vehicle. Utmost care should be taken when modifying anything to your suspension. Injury to you, your Jeep, and/or others can result from improper suspension modifications or alterations. The author is not a certified mechanic and assumes no responsibility for damage or injury.
thats off the site ^^
06-24-2007 09:47 PM
tiny terror Ok, I did keep them, pretty much brand new, but I wanked up the bolt a little on one getting it out. If you want them, PM me your addy and I'll stick them in the mail for you.
06-24-2007 09:43 PM
nicolas-eric home made discos:

cost only about 5$
06-24-2007 09:41 PM
dwdrums801 i might have some back home...I wont be home for another 2 weeks so ill check when I get give them to you for the price of shipping
06-24-2007 09:40 PM
tiny terror I'll look, I think I kept mine. You can have them if I did.
06-24-2007 09:34 PM
Sway bar disco's

I was wondering if anyone had any advice about making quick disconnects?? I would love to have a set, but would not use them enough to justify spending 140 bucks on a set!! I have a couple of ideas that I think would work if I could get my hands on a set of stock sway bar links!! If anyone has any suggestions, or has a set of stock sway bar links that they would part with cheap, let me know!! Thanks!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 04:35 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC