Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Changing Ring and Pinion Gears

Join Wrangler Forum Today


Thread: Changing Ring and Pinion Gears Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-07-2007 04:36 PM
18derrick If you want to go to 4.10 gears do like he said and find a set of axles from a 4cyl. jeep. they have the gears you want and they would just be a bolt in of around 300 bucks. I am going to have a set but you are way to far and I dont think it would be worth shipping.
07-07-2007 12:44 PM
NalinMFG would someone mind elaborating on everything needed to regear? i have a 98 4.0 with 33's on 3.73's. 35 in the back and 30 in the front. i thought i read somewhere else that if i go to like a 4.56 i need to SWAP alxes! because theyre not big enough? i saw 4x4groupbuy has front/rear with overhaul kit for $460. is that all i'd need to buy or do i need bigger axle's/housings? i dont do the whole jacked sideways rock crawling, just some trails/mud/DD. any input you guys got i'd appreciate it- thanks

http://www.4x4groupbuy.com/store/sup...ts-p-5219.html

also, how hard is this to do yourself? i know my way around the toolbox, but i didnt know if this is like "auto transmission surgery"... something i do need to pay a professional to do so i dont screw it up.
07-04-2007 11:31 PM
MoA so im guessing runnin 4.10 front and 4.11 rear would be good with 33s?
07-04-2007 11:23 PM
whitebuffalo randy's ring and pinion

http://www.ringpinion.com/
07-04-2007 11:15 PM
MoA whats a good site to buy the gears off of?
06-10-2007 11:09 AM
fly's~yj with a 4.0 if you go up to 33's you will need to re-gear..i suggest a 4:10..there are lots of gear co. that make a nice gear set..yukon, dana..etc..you will also need to get a larger carrier, and install kits..it's also a good time to, install new bearings and seals..possible locker, 30 spline shafts..etc.. or try looking around for a wrecked 2.5/4cyl..and just swap the whole assemblys..they came with 4:10's..or think about an 8.8 out of a ford..lots of options..
06-10-2007 12:56 AM
jeeps&comics 4.0 with manual tranny
06-10-2007 12:34 AM
fly's~yj what motor do you have? 4.0 or 2.5?
06-09-2007 10:49 PM
mrbigjeep definitely regear...it will restore a lot of power that you lose. you don't have to do it right when you get the bigger tires but you'll probably wanna regear later on down the road anyway...

who knows though...you may be fine with the way it drives with bigger tires so wait until you've drove with the big tires for a while and then decide.

regearing is very expensive but most definitely worth it if your feeling a power loss which is definitely possible especially on the highway.
06-09-2007 04:34 PM
jeeps&comics
Changing Ring and Pinion Gears

Ok, thanks to everyone who helped me out on deciding on a body or suspension lift.. (i think im going to go with a 2-2.5" suspension lift, but prob 2", and a 2" body lift)... after seeing odd is he's jeep, i think i too am going to run 32-33" tires on it, but this leads me to my next question...

When i install the lift(s) with the new tires, i think i am most likely going to have to change the ring and pinion gears on both the front and back. Am I correct in thinking this? and do you guys have any reccomendations as to what size gears, what brand and all that stuff. Any information you guys have is greatly appreciated. Thanks again...

:o i feel kinda retarded for asking all these questions, but like i said, im pretty much starting from scratch with this jeep, so i have a LOT of questions... thanks guys

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:18 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC