|04-27-2012 05:56 PM|
|merlinmaine||Peepers , can you describe the pin? I have the door apart and can move all the rods etc, but can't get the claws to release.|
|01-28-2011 11:05 AM|
|sevenservices||yeah 20 minutes to get the door apart and about 5 seconds to replace the broken clip...|
|01-27-2011 07:32 PM|
|blackwrangler357||lmao its easy fix takes 20 mins get panel off|
|01-27-2011 02:43 PM|
Same thing just happened to mine today at the first stop of a six stop errand run. Lots of funny looks from people watching me crawl in and out of the passenger side.
Thanks for the info - I will be putting it to good use tonight.
|01-21-2011 11:20 PM|
|blackwrangler357||i got the door panel off the rod fell off the door handle broken clip lol im good now|
|01-19-2011 12:09 PM|
|Peepers||The door handles pull a pin so the claw part that grabs onto the door pin can swing freely.|
|01-19-2011 11:59 AM|
|blackwrangler357||yea the inside and outside handle both dont work lol i can see were the door latchs shut to can i pri up on both the claps that hold the door shut and get them to release isnt that what the door handles does pulls the to claw looking things apart so the door can open|
|01-19-2011 09:03 AM|
You might have to pull your drivers seat out to have enough room. but you need to remove the door panel, once its off it should be easy to get your door off and bring it in to fix it.
I just had to do this to my door last week (TJ)(only broke the outside handle). make sure you GREASE everything when you put it back together, I think this was my problem, the cheap lube I used wore away and the friction caused things to be bent until it slipped.
|01-18-2011 11:26 PM|
if it is a typical jeep half door it is easy, well easyish with the door closed. if you have a soft top on you can follow the below step if you got a hard top...GL.
there are 3 torx screws, 2 holding the door pull handle and one in the door opening handle area. after that you have to find a way to remove the upper halves of the door. im sure you could remove the top partially so you can get access to the upper door sealing surface and unlatch that then remove the upper halves.
next remove the 3 square looking things that the upper halves slide into after that the door panel is only held in place by push pins or what i like to call christmas trees, becareful if the plastic is cold as u dont want to snap it.
once the door panel is off youre on your own as ive not gone digging in the door much, but theres not a whole lot in there just door rods for the locks and latches.
hope at least a little bit of this helped
|01-18-2011 07:55 PM|
|gennybro||Well now,maybe just get out the oxy actelene torch and start cutting away,[only kidding] It is kinda funny though,unfortunatly you dont see it that way. Is it a solid door,cloth,what is it?Can ya post a picture of it.Can ya maybe unbolt it from the hinge side of the door> ya just dont give us any information to give you any suggestions on helping ya out.|
|01-18-2011 07:49 PM|
I replaced one... Look up the handles on eBay or JC Whitney or something... When my handle was missing, I would reach in the outside and grab the rod. Push it down to open the door.
There are two retaining clips on the inside holding the handle in. They slide up and out, then the handle will drop to the outside. Simple rod w/clip connection. But, you have to pull your inside door grab handles and window cranks. Then disconnect the bottom of the door panel, lift up and it should come off. With the panel off, its much easier to work with.
|01-18-2011 07:43 PM|
|01-18-2011 05:52 PM|
|blackwrangler357||what has nobody ever had this happen to them lol|
|01-18-2011 05:04 PM|
driver door stuck closed
long story i broke the outside handle first nite froze so i was like no big deal fix it in summer well then last nite inside handle broke so now its just closed how do i get the door to open when its shut closed and both latchs broke and what parts am i lookin at needing and its on the driverside help