Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   TJ General Discussion Forum (http://www.wranglerforum.com/f282/)
-   -   lets see your front and rear bumpers!!!!! (http://www.wranglerforum.com/f282/lets-see-your-front-and-rear-bumpers-144212.html)

craigsimons3 03-05-2012 12:00 AM

lets see your front and rear bumpers!!!!!
 
looking for some new bumpers if you have any pics of yours show em please, and say who makes them. thanks

JPetru82 03-05-2012 12:03 AM

2 Attachment(s)
smittybilt SRC front and rear:


Attachment 102320



Attachment 102321

NickDanger 03-05-2012 12:10 AM

http://i17.photobucket.com/albums/b5...54032822_0.jpg

Smittybilt Stinger, picked it up for $199.99 at 4wheelparts when it was on sale for a bit, even at normal retail it was only like $249.99 I think.

TnDz TJ 03-05-2012 06:29 AM

Let's see your front bumpers!!
custom fab.
Show off your bumpers!
I wanna see your bumpers


Here is my front... ( pasted from a link above...:D )

.120 wall 2x6 metal
a little cut, grind and weld...
http://www.wranglerforum.com/attachm.../bumper002.jpg
http://www.wranglerforum.com/attachm.../bumper004.jpg
1" solid steel tow points with 7/8" eyelets
http://www.wranglerforum.com/attachm.../bumper005.jpg
And finished off with Plasti-Dip!
http://www.wranglerforum.com/attachm.../bumper007.jpg
http://www.wranglerforum.com/attachm.../bumper006.jpg
And with my Engo E12000 installed with a Smittybilt raised winch plate and Hella 500FF's


http://www.wranglerforum.com/attachm...1&d=1319985719



http://www.wranglerforum.com/attachm...1&d=1319985749



http://www.wranglerforum.com/attachm...1&d=1319985755



http://www.wranglerforum.com/attachm...1&d=1319985767

TnDz TJ 03-05-2012 06:32 AM

REAR:

.25" wall 3x4 tubing for the main body at 60" wide. Yeah... I know... it's wide, but I wanted a bit of extension on each corner for protection.

The 1" thick tow points drilled to 7/8" eyelets go completely through the entire bumper and welded under the pads 100%
http://www.wranglerforum.com/attachm...3/rbmpr001.jpg
The mounts are .25" plate material backed by 4x4x.25" pads backing the bumper.
http://www.wranglerforum.com/attachm...3/rbmpr002.jpg

The receiver is custom by me and clearance through the back. the recessed 7 -way RV connector was the add-on for future tows of a boat or small trailer.
http://www.wranglerforum.com/attachm...3/rbmpr003.jpg
and freshened up with paint and mounted for now while I go into design on the swing-away carrier.
http://www.wranglerforum.com/attachm...3/rbmpr004.jpg
http://www.wranglerforum.com/attachm...3/rbmpr005.jpg

The pivot point of my swing away is made of SS that I cut down to fit some Timken Bearings and Races for a 1.25" shaft.
http://www.wranglerforum.com/attachm...3/pivot001.jpghttp://www.wranglerforum.com/attachm...3/pivot002.jpg

End caps from mild steel stock and cut to accept shims to tighten bearings for pre-load once all is mounted on the swing-away.
http://www.wranglerforum.com/attachm...3/pivot003.jpg


STILL havent finish the swing-away... sigh....

Q_The_Cop 03-05-2012 06:51 AM

1 Attachment(s)
Smittybilt SRC front bumper. Got the matching rear on order.


Attachment 102336

xndrxw 03-05-2012 08:00 AM

Rear
http://cdn.wranglerforum.com/attachm...7&d=1330475896
front
http://img.photobucket.com/albums/v1...107_160629.jpg

IronManT28 06-17-2012 10:46 PM

1 Attachment(s)
Front

baerbonesjones 06-18-2012 06:21 AM

a resurrected ARB bumper, on my thrash wagon,
http://i236.photobucket.com/albums/f...t/DSCF3009.jpg

cphilip 06-18-2012 07:36 AM

Stock! :D

http://i142.photobucket.com/albums/r...p/IMG_1428.jpg

shipjim 06-18-2012 10:36 AM

2 Attachment(s)
[ATTACH]Attachment 133075[/ATTACH][ATTACH] I have a custom front and dirtworxx rear swingaway

TJDave 06-18-2012 11:06 AM

Smittybilt SRC Classic el-cheapo bumpers. Rear is bumper only. I would not recommend their tire carrier version. Less than $100 each. They have held up to some moderate abuse. Not even close to the strongest out there, but If I mess one up, i'm not out $400 bones a piece. It's just a bumper.

I use a Bestop tub mounted tire carrier.

http://i273.photobucket.com/albums/j...22424972-1.jpg

http://i273.photobucket.com/albums/j...1334452061.jpg

Donkerz 06-18-2012 11:31 AM

Quote:

Originally Posted by JPetru82 (Post 2104150)
smittybilt SRC front and rear:


Attachment 102320



Attachment 102321

How was the winch installation on those bumpers? I love them but I need to also install a winch :(

GoldenSahara00 06-18-2012 12:37 PM

2 Attachment(s)
Stinger made by me and stock rear bumper cut down etc.


All times are GMT -5. The time now is 02:56 AM.