Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   Classifieds Archive (http://www.wranglerforum.com/f135/)
-   -   AR: E-locker for Dana 30 27 spline.. (http://www.wranglerforum.com/f135/e-locker-for-dana-30-27-spline-151868.html)

locked 04-07-2012 12:03 AM

2 Attachment(s)
Bought this and got it put in my diff all bolted up ready to roll and as soon as i slid the axle shafts in I realized it would not work, I have 30 spline upgraded front shafts and this locker is for 27 splines...company wont take it back now im sure...I havent opened any of the electrical components at all...Locker hasnt had power hooked to it. I had to uninstall and put my old stuff back on, when i did I had to break a small retaining tab that holds the electro magnet still while the diff is in motion, there is one on the bottom also (still functional) , i ground it off and it can be reattached- I did this because i had to get the ring gear off and had already pressed carrier bearings on and could not remove them to take electro magnet off (required before ring can be added) ...so I have a brand new e locker with carrier bearings already attached to it and no use for it..Im not going to down grade axles- so Ill order another 30 spline e locker for it and sell this whole setup for $650. Ill ship wherever as long as you pay for it. I paid $800 for this setup so I am losing money. pm me if you would like it. Will come in original box with all paperwork and parts (its new)
thanks!

smccollamjr 04-07-2012 06:59 AM

Is this open or limited slip when the switch is off?

Landshark 04-08-2012 11:28 AM

Is this a reverse 30 Locker???

locked 04-08-2012 11:49 AM

Quote:

Originally Posted by smccollamjr
Is this open or limited slip when the switch is off?

Open.. Not going to be limited.. It's locked or open. For a stock Dana 30, 27 spline axles. Not reverse

jutgin 04-08-2012 03:29 PM

Whats the part number?

locked 04-08-2012 03:37 PM

Quote:

Originally Posted by jutgin (Post 2233946)
Whats the part number?

EAT19818

That should be it, not with it now, but that came from ebay site..3.73 and up dana 30, 27 spline

smccollamjr 04-08-2012 04:21 PM

Quote:

Originally Posted by Landshark (Post 2233389)
Is this a reverse 30 Locker???

I don't THINK it matters. I know a D30 carrier will work in a HP or LP. You just have to have the correct ring & pinion.

locked 04-08-2012 04:34 PM

Quote:

Originally Posted by smccollamjr

I don't THINK it matters. I know a D30 carrier will work in a HP or LP. You just have to have the correct ring & pinion.

Indeed, it's all about pinion.. Glad you mentioned.. No gears are with this locker. I have 4.88's

locked 04-17-2012 05:13 PM

Buy this folks, you know you need it.. its CHEAP!

whY402Jay 04-17-2012 09:57 PM

Wish it was mine.

whY402Jay 04-18-2012 08:47 AM

Bump

locked 04-20-2012 03:17 PM

Cmon folks! Great buy!

07XMan2Door 04-22-2012 11:41 PM

Where ya located???? How can the busted tab be fixed???

locked 04-24-2012 07:35 AM

Quote:

Originally Posted by 07XMan2Door
Where ya located???? How can the busted tab be fixed???

Small tack weld, jb weld.. Probably wouldn't even need it back on. It has another one on top. I'm in arkansas

locked 04-27-2012 05:45 AM

Yo!

locked 04-29-2012 04:46 PM

Killin me.. $600

jkaufman_95 04-29-2012 05:17 PM

I'll give you a have chewed Pack of gum and a shiny nickel :D

locked 04-29-2012 06:07 PM

Quote:

Originally Posted by jkaufman_95
I'll give you a have chewed Pack of gum and a shiny nickel :D

Is it spearmint? If so... Is there any flavor left?

jkaufman_95 04-29-2012 08:01 PM

Quote:

Originally Posted by locked

Is it spearmint? If so... Is there any flavor left?

Yes, and yes! Deal?

locked 04-29-2012 08:33 PM

Sold! Lol

jkaufman_95 04-29-2012 08:34 PM

Quote:

Originally Posted by locked
Sold! Lol

Alright! I'll send you my address lol

liredneck 05-01-2012 02:33 PM

So this would work with a hp30?

whY402Jay 05-01-2012 05:05 PM

Quote:

Originally Posted by liredneck
So this would work with a hp30?

That's what he said.

locked 05-01-2012 09:02 PM

Quote:

Originally Posted by liredneck (Post 2323332)
So this would work with a hp30?

yes, pinion location makes no difference.

locked 05-13-2012 02:22 PM

Get this out of my garage please!

BigGreenMachine 05-17-2012 11:23 AM

Quote:

Originally Posted by locked
Get this out of my garage please!

You still have it?

locked 05-17-2012 07:54 PM

Sold.


All times are GMT -5. The time now is 02:04 PM.