Jeep Wrangler Forum

Jeep Wrangler Forum (
-   TJ General Discussion Forum (
-   -   Need help with the YJ-TJ project!! (

cherokee980 02-08-2008 04:28 PM

Need help with the YJ-TJ project!!
Ok, so here is the senario. I too it out for a "road test" a few minutes ago..when I got down the road, I stopped and pulled the auto shift all the way back to low..gassed on it a little and it stumbled, and fell on it's face, and died. When I tried to re fire it, the key did nothing. I pulled it back into low and back to park. I tried it again and it fired up. On the way back to the house it spit and sputtered, and the gauges were going nuts. I got to my drive way and it was idling just fine. Pull it in the garage, shut it off, tried to refire, and nothing, and now my digital odometer is flashing between the mileage and "no BuS" What the hell does that mean? Any ideas?

Triple88a 02-08-2008 04:33 PM

its not a BUS, how hard is that to understand?. hhmm let me see if i can find u some info on yahoo.

BTW no check engine light?

Triple88a 02-08-2008 04:37 PM

OK i got you a hook.

A wiring harness behind the dashboard was faulty and intermittently would cause the speedometer and tachometer to stop working and go down to zero. When this occurred the odometer that tells you how many miles you have on your Jeep would read " NO BUS". I found out there was a service bulletin out on this problem and my dealer fixed it. "few minor problems" paragraph

Triple88a 02-08-2008 04:41 PM

read post 3.

cherokee980 02-08-2008 04:55 PM

Cool trip thanks! I actually went back down to the garage and was messing with it, and well..I don't have the fuse box mounted yet you see, and as I looked on the floorboard, I see a 15 amp fuse laying there..I pull the fuse panel from behind the other wires where I had it 'stuffed", found where the 15 amp fuse came from, plugged it back it, and viola!!! It cranked right just to check, I pulled that fuse again, and it died immediately!!! I think that was my problem.. I did how ever get a few trouble codes...


cherokee980 02-08-2008 05:14 PM

Got the trouble codes down to (2)


Triple88a 02-08-2008 05:16 PM

P0700 EATX Controller DTC Present This SBEC III or JTEC DTC indicates that the EATX or Asin controller has an active fault and has illuminated the MIL via a CCD (EATX) or SCI (Aisin) message. The specific fault must be acquired from the EATX via CCD or from the Aisin via ISO-9141.

P0443 (M) Evap Purge Solenoid Circuit An open or shorted condition detected in the EVAP purge solenoid control circuit.

P0113 (M) Intake Air Temp Sensor Voltage High Intake air (charge) temperature sensor input above the maximum acceptable voltage.

did you ever connect the breather hose? that also throws a code, mine did.

Triple88a 02-08-2008 05:23 PM


NVLD Canister Vent Valve Solenoid Circuit High

A shorted high condition detected in NVLD solenoid circuit.

Triple88a 02-08-2008 05:24 PM

P0443 (M)

Evaporative Emission Control System Purge Control Valve Circuit

An open or shorted condition detected in the EVAP purge solenoid control circuit. Check the charcoal canister for fuel saturation If the vehicle has been overfueled, then there is a chance that liquid fuel can enter the canister and cause drive problems or emission related problems.

cherokee980 02-08-2008 05:29 PM

Yea, I disconnected the battery and got rid of all but those (2) P0499 / P0443. i dont have any ove the purge evap system hooked up. It was destroyed on the wreck of the '05. I guess I will have to live with these codes. I did fire it back up and take it down the road again. Ran great. i even did a little do-nut!!!

cherokee980 02-08-2008 07:51 PM

problem solved! thanks trip!!!!!

All times are GMT -5. The time now is 07:57 PM.

User Alert System provided by Advanced User Tagging v3.1.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.