Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   General Jeep Discussion (http://www.wranglerforum.com/f19/)
-   -   Independent from chassis tub ? (http://www.wranglerforum.com/f19/independent-from-chassis-tub-193165.html)

div4gold 10-14-2012 12:01 PM

Independent from chassis tub ?
 
This is a ad I came accross the seller says that the tub floats and is independent from the chassis, anyone know what he means by that?




* 1949 Willys Jeep CJ2a * GREAT Project Crawler lots of potential! - $4900 (VANCOUVER)

Date: 2012-10-10, 7:35PM PDT
vr4fx-3330659332@sale.craigslist.org [Errors when replying to ads?]
NEEDS SMALL AMOUNT OF FABRICATION AND ASSEMBLY. IF YOU WANT TO KNOW HOW MUCH PLEASE JUST CALL AND MAKE AN APPOINTMENT TO LOOK!

Lots of goodies come with this project jeep. Call or txt ME with any other questions, please no scammers 36zero-5two4-one897. ** NO EMAILS **

THE RUN DOWN ON THE JEEP

REBUILT SMALL BLOCK CHEV 350

ADVANCED ADAPTERS HEADERS NEW

STAINLESS SUPERTRAP EXHAUST WITH BAFFLES NEW

EDELBROCK 600 CFM CARB NEW

K & N HIGH FLOW AIR FILTER NEW

ALUMINUM WATER PUMP NEW

ALUMINUM BILLET POWER STEERING PUMP NEW

SINGLE WIRE ALTERNATOR NEW

FLUID AMPH DAMPENER NEW

ALUMINUM RACE SPEC GAS TANK W/ ANTI BACKFLOW NECK NEW

ELECTRIC FAN WITH SHROUD AND THERMOSTAT NEW

PAINLESS WIRING HARNESS NEW

4 CORE ALUMINUM RADIATOR NEW

HEI HYFIRE MALLORY DISTRIBUTOR NEW (INCLUDES: MALLORY 6AL BOX AND MALLORY LED DISTRIBUTOR - used)

BRAKE MASTER CYLINDER NEW

CLUTCH MASTER CYLINDER AND SLAVE CYLINDER NEW

STAINLESS STEEL BRAKE LINES NEW

5 - 36" BUCKSHOTS

5 - 16.5 ALUMINUM RIMS NEW

2 - RCI 5 POINT HARNESSES IN THE BOX NEW

DUAL RS 9000 SHOCKS WITH REMOTE ( ALL AROUND ) NEW

GM CARBOX 4 SPEED

DANA MODEL 20 TRANSFER CASE

FULL WIDTH CORPORATE 14 BOLT REAR END

FULL WIDTH DANA 44 FRONT END

3 - CUSTOM UPHOLSTERED SEATS

ALL DASH GAUGES

MANY, MANY MISCELLANEOUS EXTRA PARTS AND PIECES

HEADLIGHT BEZELS, BLINKER LIGHTS, TAILLIGHT BEZELS ETC.

WHAT IT NEEDS: THE TUB FLOATS INDEPENDENTLY FROM THE CHASSIS. HAS THE MAJORITY OF PARTS TO FINISH BUT WILL NEED SOME SMALL FABRICATION AND A LOT OF WRENCHING.

Q: Do you have receipts for the work and or parts on the engine and and trans, etc.? What all was done to the motor for the reubuild? Do you know whaqt era the motor is from?
A: Yes, I have many many receipts, though not all as this was built 15 years ago. The engine is a fresh rebuild that has been run and seasoned. BLOCK cast #3970010 the run was 69-80, the HEAD cast #3998991 the run was 72-73 it is a 75cc chamber they came in 194s & 202s could be either or? This was built to be a good solid engine and to run cool, no big cam, just a solid runner with new everything. Whoever buys this can pull the pan before they take it to see the work.

Q: IS THE FRAME THE ORIGINAL 1949 JEEP?
A: No , it is a 3/4 bowed frame

JTE 10-20-2012 10:25 AM

I read it as needing brackets fabricated to the frame to attach the tub.


All times are GMT -5. The time now is 09:46 AM.