Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   TJ Build Forum (http://www.wranglerforum.com/f322/)
-   -   aTX427's TJ Build thread (http://www.wranglerforum.com/f322/atx427s-tj-build-thread-225950.html)

aTX427 03-07-2013 01:43 PM

aTX427's TJ Build thread
 
I had a few requests for a build thread, so here it goes. Unfortunately, I did not document the process for a lot of my mod's, but I will try to help answer questions the best I can. My intent it to help you make better decisions with the future mods and hopefully save a few dollars along the way. - enjoy

To start off, this is my first Jeep and it's purpose has changed a few times in the two years I have owned it. It started life off as a bone stock 99 Sahara hard top with a factory D44 rear axle a white exterior and camel interior. It was originally going to be stripped out for a hunting rig; however, I wanted to run 35's and fully bed line exterior to protect the paint from the harsh south Texas terrain. For this purpose, I purchased Metalcloak front fenders and had the paint sprayed with Superliner, a bed liner product produced in Austin, TX. They were local and very reasonably priced.

Here is ROK 1 - version 1 stripped down for hunting - stock lift.

http://i55.photobucket.com/albums/g1...epsideview.jpg

Keep in mind, I had never been rock crawling or off roading for that matter since I was a child in my buddy's CJ5 some 30 years ago. I have had trucks and dirt bikes, but never intended to crawl. My first trip out was the dove season opener, where I realized that 35's on stock suspension was not going to work. With four of us in the Jeep, I bottomed out all weekend long, so it was time to research lift kits.

I knew I did not want to go too high, partially because I could not afford a long arm and I did not want to weld, but mostly because I wanted to stay low COG. Little did I know low COG would cost more in the long run and welding is a big part of owning a Jeep :).

After a bit of research, I ordered up an OME 2.5" lift with a steering stabilizer, an SYE, Currie front and rear track bars, a set of Currie upper rear control arms, a UCF no-BL needed aluminum skid, along with a Currie Anti-Rock front sway. I installed the lift myself and have a local shop do the SYE.

http://i55.photobucket.com/albums/g1...Jeep/jeep2.jpg

OK, so now I have to admit, the off roading bug started nibbling and last winter I decided to take a trip to Hidden Falls, a local off road park less than an hour away. I thought this as pretty radical at the time. Little did I know that would change as well. Rock crawling is a lot more fun than I thought it would be.

http://i55.photobucket.com/albums/g1...p/IMG_1011.jpg

Next, I decide that I want to go for an off road excursion over the summer and pick the Lake City / Telluride area for a two week overlanding trip with my GF. Having never done a trip like that before, I decide to take the Jeep to the next level. For mods, I add a Warn M8000s winch, a UCF aluminum winch mount, 4.88 gears, ARB lockers, a spare wheel assembly, a Rancho rear bumper / tire carrier, a custom Rotopax water / fuel system, Metalcloak 6" front / rear fenders, a Smittybilt CRES and a custom aluminum safari rack. I also decided to re-purchase a set of full doors and a hard top, as I sold the original parts to fund my first round of mods. We were determined to rough it, so we left the hard top home and drove out topless. It was hotter than hell driving through west Texas and rained every day in Colorado. Should have thought that one through as well.

http://i55.photobucket.com/albums/g1...p/IMG_1304.jpg

http://i55.photobucket.com/albums/g1...p/IMG_1282.jpg

Loaded for bear and away we go. By far the coolest trip I have ever taken. We hit all the main trails including Black Bear and Poughkeepsie Gulch, which had a sign warning travelers that winches and lockers were highly recommended. How bad could it be? ...so we decide to traverse it at dusk in a down pour. Not one of my better decisions, but we made it out safely and decided to try going up the gulch the next day after everything dried up.

http://i55.photobucket.com/albums/g1...p/IMG_1305.jpg

http://i55.photobucket.com/albums/g1...p/IMG_0643.jpg

http://i55.photobucket.com/albums/g1...5at11638PM.png

After returning, I realized my rear springs were no match for the weight we were carrying and decided to learn spring / suspension technology. After experimenting with several spring rates, I decided to remove the stock spring dampener, replacing the front with a 1.25" spacer and the rear 160# OME 942 springs with a heavier rate LJ 949's at 216# and a 1.75" spacer. This drastically improved the loaded ride height and did not affect the unloaded ride in any way whatsoever.

I also found that having a .5-.75" rake with a heavier rear spring radically improved the climbing characteristics while rock crawling. Prior to this change, the rear was loading over uphill obstacles and unloading the front, which was causing major problems over advanced terrain.

http://i55.photobucket.com/albums/g1...1222DC1AB0.jpg

This was my first trip out to Katempcy Rocks K2, AKA, the Moab of Texas. Their easiest trails are like the hardest trails at Hidden Falls. OK, sink or swim - I'm going rock crawling...in the rain no less.

http://i55.photobucket.com/albums/g1...psf5983736.jpg

http://i55.photobucket.com/albums/g1...ps0a81874e.jpg


So, I learned another valuable lesson, trying to carry extra fuel, water is best left for overlanding. I didn't like the tire carrier banging into my tailgate and drug my tire in the dirt trying to get over that Bus Stop. I also banged the crap out of my stock gas tank skid and bent my lower control arms. Time to do more research.

The next phase of mod's included selling my rear bumper tire carrier and UCF low clearance skid, then ordering a full set of Rockmen LCA's, a UCF no body lift needed aluminum gas tank skid, a UCF Ultra low aluminum transfer case skid, a UCF low profile transfer case mount and a Novak shifter cable.

I chose the Rockmen LCA's because I liked the fact that they were oversized. 1.75" lower ams and 1.25" uppers with Johnny Joints on all ends. I changed out the front lower axle mounts with the Johnny Joint set up as well. Now I am JJ on every joint, I have the pinion set up well, stretched the arms back to retain stock wheelbase and take my Jeep to a suspension specialist who dials in my alignment, which removed any shimmy whatsoever from the ride quality. I am simply amazed how well this Jeep drives.

I can cruise 75-80 mph on the highway like it is nothing. I also experimented removing my rear sway bar and hated it. The handling was downright scary and there is no way I could drive on road that way. Testing on an RTI ramp proved that there was a minimal gain in stretch from removing the sway and an increased amount of body roll offroad, so back on it went.

The next set of improvements included suspension seats, outboarding my rear shocks, a full sport cage, shaving my lower LCA mounts, a 40" LED light bar, rock lights a Tuffy conceal carry storage drawer, a Tuffy oversize rear storage drawer, a custom aluminum rear storage tray, an Agate interior swap, an 03 switch panel replacement, a set of Savvy aluminum rear corners, relocated my Hi-Lift to the hood, I mounted my spare inside the cab for now and a Savage bowless soft top, which does fit over a Poly rear sport cage, just in case anyone is interested.

Here are how things stand today. Happy Jeeping
http://i55.photobucket.com/albums/g1...ps6c7d370d.jpg

http://i55.photobucket.com/albums/g1...pse8447947.jpg


http://i55.photobucket.com/albums/g1...ps4f667ba9.jpg



PRP Podium suspension seats
http://www.wranglerforum.com/f5/my-n...ts-204124.html

Out-boarded my rear shocks
http://www.wranglerforum.com/f5/out-...ks-202151.html

Sport cage install
http://www.wranglerforum.com/f5/my-s...ll-194405.html

40" TWF light bar
http://www.wranglerforum.com/f5/twf-...ed-225920.html

Rock light install
http://www.wranglerforum.com/f5/cust...ds-225924.html

99 to 03 switch panel replacement
http://www.wranglerforum.com/f5/inst...-a-204126.html

Savvy aluminum rear corners / tailgate cover
http://www.wranglerforum.com/f5/meta...er-225913.html

Safari Rack and tire carrier systems
http://www.wranglerforum.com/f5/fabd...od-178399.html

Cheap Hi-Lift hood mounts
http://www.wranglerforum.com/f5/hi-l...ap-204129.html

Interior mounted spare
http://www.wranglerforum.com/f5/moun...ow-204127.html

dingos_unlimited 03-07-2013 03:45 PM

Well done. That's how a jeep should look. So your exterior color is the bedliner type product?

aTX427 03-08-2013 03:00 PM

Yes, it is bed lined inside and out with a product called Superliner based out of Austin, TX

Gunner 03-08-2013 06:32 PM

Awesome Jeep. Nice write up too.

Rusty762 03-18-2013 03:22 PM

Rok I stumbled on your post on Jeep Forum, love the rig man you should post a build thread on JF!

PaulisTJ 03-18-2013 06:21 PM

I have decided that I'm also going to bed line my exterior just like yours(same color), mine is also a sahara. Hope you don't have me too much for taking your idea.

1ofakind 03-21-2013 11:21 AM

that is an AWESOME color! rig looks wicked! subscribed! ;)

Csahara 03-21-2013 12:26 PM

Sick TJ

Imped 03-21-2013 12:50 PM

Well done rig so far.

mvallen 03-21-2013 01:57 PM

Nice! Using your rig as an inspiration! Subscribed!

00tj2 03-21-2013 02:48 PM

That bedlinner looks great, and so does the color.

RedTJ00 03-21-2013 03:20 PM

nice rig love the look of it.....the front fenders are they the 4" arch or the 6" arch ?????

1ofakind 03-26-2013 12:32 PM

Quote:

Originally Posted by RedTJ00 (Post 3534432)
nice rig love the look of it.....the front fenders are they the 4" arch or the 6" arch ?????

I believe he said 6" correct me if im wrong

aTX427 03-26-2013 01:40 PM

Correct they are 6"

jwcom93 03-26-2013 02:39 PM

Subscribed

1ofakind 03-26-2013 02:48 PM

Quote:

Originally Posted by ROK1 (Post 3555212)
Correct they are 6"

How is the bedliner holding up? Id likr to do this to my 98 tj. I gravel guarded my lasr jeep inside and out but sold it almost right after, turned out great but never got a real test of durability. Im going to one day monstaline the whole jeep

NC Bear 03-26-2013 02:56 PM

I love the color, nice rig!

1ofakind 03-26-2013 03:03 PM

Quote:

Originally Posted by ROK1 (Post 3555212)
Correct they are 6"

How is the bedliner holding up? Id likr to do this to my 98 tj. I gravel guarded my lasr jeep inside and out but sold it almost right after, turned out great but never got a real test of durability. Im going to one day monstaline the whole jeep

aTX427 03-26-2013 08:41 PM

Mine is sprayed with Super liner, a product sold in Austin TX.
It holds up well against everything except sliding on rocks, but not much does.

aTX427 03-26-2013 08:42 PM

Quote:

Originally Posted by NC Bear (Post 3555445)
I love the color, nice rig!

Thank you - it actually has a bit of sparkle in the sun.

kpla51 03-26-2013 09:17 PM

iv been looking at the metal cloak fenders and there website doesn't make much sense to me what all do you need to buy and how much did it cost? it shows the flares separately?

1ofakind 03-27-2013 12:19 AM

Quote:

Originally Posted by ROK1 (Post 3556885)
Mine is sprayed with Super liner, a product sold in Austin TX.
It holds up well against everything except sliding on rocks, but not much does.

do they have a website?

EMTJEEP 03-27-2013 01:27 AM

Quote:

Originally Posted by kpla51 (Post 3557070)
iv been looking at the metal cloak fenders and there website doesn't make much sense to me what all do you need to buy and how much did it cost? it shows the flares separately?

Go on this link Jeep Wrangler TJ and TJ Unlimited (LJ) Tube Fenders & Body Armor and just choose one of the first four selections which are fenders which comes with all the hardware and then pick one of the next six selections for flares based on if you got arched or overline if you want to add a flares. Fenders run $599-$799 and flares go from $139-$249

Bsc 03-27-2013 01:40 AM

Jeep looks great

aTX427 03-27-2013 03:32 AM

Quote:

Originally Posted by 1ofakind (Post 3557810)
do they have a website?

Bedliner.com

kpla51 03-27-2013 05:28 AM

Quote:

Originally Posted by ROK1

Bedliner.com

I wonder if you can buy it and have a body shop do it for you or someone who does truck beds

1ofakind 03-27-2013 09:35 AM

Quote:

Originally Posted by ROK1 (Post 3558081)
Bedliner.com

Thanks!!

DetroitRodeo 03-28-2013 04:28 PM

Awesome rig! I have mine fully bed lined as well (in a darker color). Love the look of yours!

aTX427 03-28-2013 07:35 PM

Yeah, I really like the bed lined finish. What did you do for the Rubicon label. Is it sprayed with bed liner or paint? Ordinary spray paint seems to take to mine very well.

DetroitRodeo 03-28-2013 08:15 PM

Quote:

Originally Posted by aTX427 (Post 3565502)
Yeah, I really like the bed lined finish. What did you do for the Rubicon label. Is it sprayed with bed liner or paint? Ordinary spray paint seems to take to mine very well.

It's just the normal decals, I clear coated them into my hood.


All times are GMT -5. The time now is 12:48 AM.