Jeep Wrangler Forum

Jeep Wrangler Forum (
-   Builders Corner (
-   -   Yj build. (

Crashzx6r 05-19-2013 04:10 PM

Yj build.
8 Attachment(s)
I have started a mild build that will progress as it completes

Yj with 350sbc
Stock axles while d60s are built 33s til d60s come then rolling on 37s

Fuel cell'd
Custom cage

Attachment 251028

Attachment 251029

Attachment 251030

Attachment 251031

Attachment 251033

Attachment 251034

Attachment 251035

Attachment 251036

Crashzx6r 05-19-2013 04:15 PM

2 Attachment(s)
Gonna be getting trans and Case ready to put I'm before I start wire harness and complete dash. Scored a z gate for 40 bucks too. The motor was supposed to be a old junk motor but when disassembled I found all new internals so I added new intake and carb.
Ill be at least to a point it can run and then ill make decision to speed up and buy tons or play with stock axles and get some reward.

Attachment 251038

Attachment 251039

Over the weekend I rebuilt springs and installed greaseable shackles. Will be soauntil d60s then probly 4 link and coil overs if the wife doesn't kill me. More progress to come

Crashzx6r 05-19-2013 04:22 PM

I hope to have the following set up when it's supposedly "done"

D60 with some bling parts like ried racing knuckles chromo shafts and Detroit
Rear stretch with d 60 chromo shafts locked and disc conv
Fuel cell
Custom dash auto meter gages
Custom center console from dash etc
Custom cage

For now it will get 350/th350/np241 and stock d30 and d35 with 4.11 and 33s
Cage fuel cell and custom dash ect
Basically everything but case and axles will be complete so when funds allow rock ready axles the rest of the jeep is already complete but in mean time I can be playing / breaking it while axles are on my bench. Ill try to get more details and steps as I go but this is a weeks worth.

I will post all fab and build stuff as I go from here.

Crashzx6r 05-19-2013 04:31 PM

4 Attachment(s)
Attachment 251048

Here's a shot of the 700r4 np208 I had in shop, I decided to go with th350 and 241 because I don't need overdrive and no torque converter lock up needed. Also the th350 is shorter setup helps me shorten front shaft and lengthen rear shaft. So ill e selling trans and 208 to get more funds for other stuff.


Attachment 251046

The seats pictured are bostrom air seats from a m2 freight liner ddc4d the seats are fully adjustable and with air setup I can go up and down, as well as a comfortable suspension seat.

Attachment 251047

Scored msd and some Gage's for a

Attachment 251045

Stock junk but it will do for now. Guess ill be carting around u joints and outers in the back

Crashzx6r 05-19-2013 05:20 PM

All in all I ended up with a solid fresh 350 and all I added was new carb new intake and valve covers. Looks like the new cam in it is a street strip cam. Keep your eyes on this gonna be a nice build once momentum starts rolling.

Crashzx6r 05-19-2013 07:09 PM

4 Attachment(s)
Attachment 251137

Attachment 251138

Attachment 251139

Attachment 251142

kywaterman 05-20-2013 12:48 PM

looking good, keep us posted I'll be following along

Crashzx6r 05-20-2013 04:39 PM

Thanks should get good soon.

KillerKustums 05-21-2013 07:26 AM

Looking really nice. Can't wait to see more pics.

Crashzx6r 05-22-2013 09:09 PM

2 Attachment(s)
Attachment 252483

👍 Trans and case almost ready to install.
Changed output shaft from 2wd to 4wd

Attachment 252484

kywaterman 05-22-2013 11:36 PM

Bought my motor the other day now on the hunt for a trans and tcase, did you have to use any adapter for the th350 to 241? And how much shorter is the 700r 208 combo than the 350/241, roughly? Looking good as I said earlier man, might have more questions for you later on lol

Crashzx6r 05-23-2013 04:16 AM

The 700r4 is almost 2 inches longer than the th350 set up. I am making a flange for the two so I will actually have 3 inches saved.

Crashzx6r 05-23-2013 04:19 AM

Your best luck would be to get a pair out of something so flange and all is there just keep in mind wranglers are short so your front driveline will be long rear shaft short regardless so that plays a factor in choices. I plan to go d300 in future with advance adapters set up.

kywaterman 05-23-2013 09:42 AM

My original plan was to use a 700r with a 241 that came behind it originally then a jb conversion super short sye to gain some length. Did you buy or build motor mounts?

Crashzx6r 05-23-2013 04:49 PM

Both, they are poly performance bolts right up. But cross bar is very close to my pan so I cut and lowered the bar. Your original plan should work just fine, and wiring the tc lock up is easy:thumb:

Crashzx6r 05-26-2013 09:55 PM

3 Attachment(s)
Attachment 254061

Attachment 254062

Attachment 254063

Crashzx6r 05-26-2013 09:58 PM

3 Attachment(s)
Here's a shot of current progress gonna be wiring dash and firing motor up tomorrow.
Next is mating trans and t case and building mounts.
Then cage work and more wiring harness building.

Attachment 254069

Crashzx6r 05-27-2013 10:28 AM

Motor is running, now I'm on to building harness for Gage's and the msd 6 plus might even put a two step button in.

kywaterman 05-27-2013 10:48 PM

looking good, like the dash :thumb:

Crashzx6r 05-31-2013 04:14 PM

Some parts came in gonna go sweat some

Crashzx6r 05-31-2013 04:15 PM

1 Attachment(s)
Attachment 256080

Crashzx6r 06-01-2013 03:50 PM

1 Attachment(s)
Attachment 256400

So don't be alarmed its 26 ft tall with nothing but the tub and motor in front It will set lower with all cage cell trans and case but its rolling on 23s

Crashzx6r 06-02-2013 06:38 PM

1 Attachment(s)
Attachment 256945

Turning into a jeep again, I'm currently mocking up seat locations and wiring I'm almost ready to finish axles and mount permantly

viperx6x9x 06-02-2013 06:56 PM


Originally Posted by Crashzx6r (Post 3815083)
Attachment 256400

So don't be alarmed its 26 ft tall with nothing but the tub and motor in front It will set lower with all cage cell trans and case but its rolling on 23s

Looking good man. Why not skip the 37's and find 3 more of those tractor tires though? :)

Scooby88 06-02-2013 09:22 PM


Crashzx6r 06-03-2013 07:38 AM


Crashzx6r 06-10-2013 10:33 PM

2 Attachment(s)
Attachment 260127

Been working on some Exo/ sliders. Gonna wrap all the way around wheel wells rockers and to bumpers then making th spare tire holder. I should be picking up the boggers and tsls this week.

Attachment 260128

5 35x14.50 r15 and 5 wheels three tsls and two boggers. 700 bucks is pretty fair.

Crashzx6r 06-12-2013 07:10 AM

1 Attachment(s)
Attachment 260574

Crashzx6r 06-12-2013 07:39 PM

3 Attachment(s)
Attachment 260739

Attachment 260740

Attachment 260741

04Xtj 06-13-2013 09:44 PM

going to be a beast..keep the pics rolling

All times are GMT -5. The time now is 03:55 AM.

User Alert System provided by Advanced User Tagging v3.1.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.