Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   TJ General Discussion Forum (http://www.wranglerforum.com/f282/)
-   -   Painted Fender Flares (Yawn) - Pics Though! (http://www.wranglerforum.com/f282/painted-fender-flares-yawn-pics-though-63707.html)

jpg103 10-01-2010 01:33 AM

Painted Fender Flares (Yawn) - Pics Though!
 
After searching through the forum for how to paint fender flares I decided to give it a go today with some Krylon Fusion in Satin Black. Rather than completely remove them, I opted to leave them on and try to make up with it in prep work. This was mainly because I didn't have an optimal work area. My only regret there is that I wasn’t able to hit the undersides of them but for now it’s fine.

I had tried almost every product (including Mother’s Back to Black) in efforts to keep the flares looking OK but none of them worked very well in my opinion. I’m convinced the fading was accelerated by my girlfriend’s liberal use of Amor All, which I think is the crack cocaine of detail products. Looks great for a day but then you need to apply more.

Photo #1: Masking and prep work. I didn’t need to loosen the flares as there was already enough play between them and the body to slide the masking paper in. This photo also shows what the flare looked like after I sanded it with 150 grain paper (I would suggest sanding as it’s very little extra work.) This was done after wiping down the freshly washed fenders with Windex to get any leftover grime.

http://i144.photobucket.com/albums/r...kgreen/008.jpg

Photo #2: Just shows the before state of the front right flare, lots of fading on the body extension portion. Sorry about the lighting in the first two photos but the was some morning fog.

http://i144.photobucket.com/albums/r...kgreen/009.jpg

Photo #3: Here’s how the right rear flare looked after about two coats compared with the front right (still unpainted.) I kind of leapfrogged around the Jeep, prepping one flare, going back and spraying another coat on the last one, so on and so forth to save time.

http://i144.photobucket.com/albums/r...kgreen/013.jpg

Photo #3: The right front flare. I just pulled the running light lens and disconnected the lighting harness, then backed the opening with masking paper.

http://i144.photobucket.com/albums/r...kgreen/017.jpg

Photo #4: Finished product – I’m happy! No more cheap, greasy shine, just a nice textured satin black now. Why couldn’t Jeep have thought of this at the factory?

http://i144.photobucket.com/albums/r...kgreen/021.jpg

Photo #5: The only screw up was leaving the masking behind the right front flare for too long, hence a little flaked off when I removed the backing. I think I can touch it up though. A guy I used to paint for taught me a long time ago to always pull your masking while to paint’s still wet to get super clean lines (wish I had remember that this afternoon.) In any event, I hope this paint job lasts because I'm not going to do it again.

http://i144.photobucket.com/albums/r...kgreen/019.jpg

So that’s it. A couple of notes: 1.) I found that the Krylon Fusion has a bit of texture when it dries so that and my OCD prompted me to hit each fender like seven time. It also meant I used almost 3 cans of Krylon. One portion of the left rear flare had some drips in it so after that coat dried, I lightly sanded it down and resprayed it. Overall time was 3-4 hours. Could have been a little faster if I had been more confident with my spray skills.

Thanks to all the member s of the forum who have posted their information here for newbies like me to find. Hope the photos help the next person.

oldskool71 10-01-2010 05:25 AM

I about to do this myself....I was planning on removing mine though...do you have to use sandpaper on them first though?..by the way thanks for taking the time to take pics and post this...very helpful.

blkrubi88 10-01-2010 06:53 AM

Flares look great!:appl:

YJjeep 10-01-2010 06:56 AM

I like the color on your jeep.
Looks sharp.

ParaCAD 10-01-2010 08:19 AM

yea thanks for posting...good job!

jpg103 10-01-2010 02:49 PM

Quote:

Originally Posted by oldskool71 (Post 796770)
I was planning on removing mine though...do you have to use sandpaper on them first though?..

I'd probably sand them after removal just so you don't have to worry about scratching the body finish. The sanding was super easy and I did it to ensure that the years silicone base products on them would be gone before painting. Good luck!

wolfen 10-01-2010 05:13 PM

Been there done that, I used Krylon Fusion for plastic things :) so far so good

OregonTJ 10-01-2010 05:40 PM

looks good..........

oldskool71 10-02-2010 03:51 AM

took the passenger side flares off this afternoon...gonna give them a shot tomorrow...wish me luck...:D

jpg103 10-02-2010 01:27 PM

Quote:

Originally Posted by oldskool71 (Post 798071)
wish me luck...:D

You'll do fine!

parcours 10-02-2010 08:45 PM

Does this count?

Line-X...

http://i334.photobucket.com/albums/m...ubi_Line_X.jpg

http://i334.photobucket.com/albums/m...i_Line_X_1.jpg

wolfen 10-02-2010 09:18 PM

Quote:

Originally Posted by parcours (Post 798821)


Now thats just plain cheating :)
nice man wish I'd thought of doing that to mine.

flyboy86q 10-03-2010 01:50 AM

I did my flares and bumpers this week. I just masked it off as well. Seemed to go faster. Mine were nearly white from the previous owner.

harwa004 10-03-2010 01:55 AM

Gotta do mine this week. Some idiot keyed my rear passenger one...DEEP.:banghead:


All times are GMT -5. The time now is 12:45 AM.