Jeep Wrangler Forum

Jeep Wrangler Forum (http://www.wranglerforum.com/)
-   TJ General Discussion Forum (http://www.wranglerforum.com/f282/)
-   -   ARB switch mounting pics (http://www.wranglerforum.com/f282/arb-switch-mounting-pics-9293.html)

richp 07-05-2007 09:54 PM

ARB switch mounting pics
 
Anybody got any pics of a 2001 TJ w/o the ashtray option. Just finished installing two arb's in front/rear D44's. Got three switches, front, rear, compressor. Tried using the two empty blanks in the panel but that little overhang on the top of the switch and the rocker type cover is not working out. Got a feeling I'm going to have to mount them in that empty square area after cutting out the 3 standoffs that were used for the airbag disable. Thanks.

4Jeepn 07-05-2007 10:06 PM

Here's where mine are.. pic's not the best.

http://i62.photobucket.com/albums/h9...k/100_1592.jpg

richp 07-05-2007 10:11 PM

Quote:

Originally Posted by 4Jeepn (Post 99907)
Here's where mine are.. pic's not the best.

http://i62.photobucket.com/albums/h9...k/100_1592.jpg


Not what I have, where your three switches are I already have 4 factory slots, 2 used for the rear wiper and rear def but the overhang on the top interferes with the arb switches and the switch cover. Where you ashtray is I have a big blank area but it has 3 standoffs behind it. Once the third switch gets here tomorrow I'll be exercising my coping saw I think. Did you cut 3 seperate holes one big one ? Thanks.

4Jeepn 07-05-2007 10:20 PM

Shop did mine for me.. I told them what I wanted, and visa took care of the rest. AEV also has one that mounts near the dash, but I think its only a two hole box.

richp 07-05-2007 10:26 PM

Quote:

Originally Posted by 4Jeepn (Post 99914)
Shop did mine for me.. I told them what I wanted, and visa took care of the rest. AEV also has one that mounts near the dash, but I think its only a two hole box.

Yea, just went out and looked at one of my 97's and they have the same setup as yours, the 01 is alot different and there is a big thick eyebrow over the factory switch holes. Well I guess if I screw up the plastic I can always use some sheet metal over that big square area.

Absolute Offroad 07-06-2007 12:15 AM

These are from a 97: [IMG]http://inlinethumb56.webshots.com/68...600x600Q85.jpg[/IMG]

Joe

erickpl 07-06-2007 07:33 AM

I've seen pics of the ARB switches mounting just fine on a 2001 and newer TJ. Over on JF... I'll see if I can find the pic..

It CAN be done. Those switches are VERY tight when you put em in.

erickpl 07-06-2007 12:58 PM

Here it is.. from an 06 LJ...

http://i123.photobucket.com/albums/o...p/DSC_0044.jpg

And here's my 97...

http://img.photobucket.com/albums/v3...l/DSCN0207.jpg

And another option if you REALLY don't want to use the stock locations..

http://img.photobucket.com/albums/v5...d/DSCN1760.jpg

richp 07-06-2007 01:13 PM

Quote:

Originally Posted by erickpl (Post 100082)

Yes, thats it, did you do them or have them done ? It is not so much the tightness it's the clearence on the top, I'm a bit squemish about cutting it too much. Looks good though.

erickpl 07-06-2007 01:35 PM

It's not mine. Found the picture on JU, not JF like I originally thought. The poster didn't mention anything about having to cut to make things fit. I know on MINE, I put one end in first, the angled the other in. It WILL be a VERY tight fit, but that is how you want it.

kavanji 07-08-2007 03:14 PM

http://i186.photobucket.com/albums/x...vanji/TJ57.jpg
switches in my RHD TJ

Timberman 01-06-2009 10:13 AM

Need an ashtray blank
 
Hey Guys,

Does anyone know where one could get an ashtray "Blank" for a 2000 TJ sport? My dilemma is that I have a hard top with wiper, Defrost, and Fog Light switches already being used. I am due to have the install done anytime now and I am really getting a little antsy about where I am going to mount the rockers for the compressor and both lockers.. :banghead:

Any suggestions are most helpful, but I really like the lay-out of erickpl's last pic..

I would really like to get a blank and just toss the ash tray!

Thanks

Timber


All times are GMT -5. The time now is 05:59 AM.