Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 9 of 9
Search took 0.31 seconds.
Search: Keyword(s): ; Posts Made By: JFSCoz
Forum: TJ General Discussion Forum 05-05-2014, 07:37 PM
Replies: 8
Views: 430
Posted By JFSCoz
could also be windshield leaking. mine leaks and...

could also be windshield leaking. mine leaks and there is a pool of water after heavy rain.
Forum: TJ Tech Forum 12-04-2013, 11:14 AM
Replies: 3
Views: 253
Posted By JFSCoz
I replaced my slave as well but when I tried to...

I replaced my slave as well but when I tried to bleed the system via the bleed screw it was useless. I had to remove the slave and pump it by hand for about 100 times ( 3 cycles). Make sure someone...
Forum: TJ Tech Forum 08-14-2013, 05:56 PM
Replies: 12
Views: 1,673
Posted By JFSCoz
Mine was doing the same thing. It was one of the...

Mine was doing the same thing. It was one of the springs on the clutch disc came off. Replaced the clutch
Forum: TJ Tech Forum 07-08-2013, 05:53 PM
Replies: 16
Views: 749
Posted By JFSCoz
I had a bleeder screw on the dorman clutch slave...

I had a bleeder screw on the dorman clutch slave I installed. I bled that thing for an hr and a half and nothing! This is the only way to get the air out of the system so pay attention to what I...
Forum: TJ Tech Forum 07-08-2013, 05:40 PM
Replies: 34
Views: 1,370
Posted By JFSCoz
I just had a new Luk installed . Clutch was $145...

I just had a new Luk installed . Clutch was $145 from NAPA. Installation here in Mexico was $100! works fantastic now.
Forum: TJ Tech Forum 05-23-2013, 12:33 PM
Replies: 1
Views: 298
Posted By JFSCoz
Rear axle seal / bearing on 2004 sahara

I noticed I have a small bit of leakage on drivers rear. Does anyone know a good replacement axle seal and bearing to get ( price too!). It looks like a dana 44 rear end. Gracias
Forum: TJ Tech Forum 05-09-2013, 08:03 AM
Replies: 12
Views: 538
Posted By JFSCoz
If you do replace slave, I would not bother with...

If you do replace slave, I would not bother with the bleeder screw on it. Just manually hand pump the slave to get the air out. I spent probably an 1 1/2hr pumping my pedal and using the bleed...
Forum: TJ Tech Forum 05-06-2013, 08:44 PM
Replies: 12
Views: 538
Posted By JFSCoz
So is the pedal soft when you push it down? Check...

So is the pedal soft when you push it down? Check for leaks on your floor? up in the firewall where the master cylinder comes in? Crawl underneath the drivers side and look for the clutch slave. Any...
Forum: TJ Tech Forum 05-06-2013, 10:39 AM
Replies: 12
Views: 538
Posted By JFSCoz
I had a similar problem. My pedal went right to...

I had a similar problem. My pedal went right to the floor (soft) and I couldnt engage gears. It was my clutch slave. Easy to replace but a pain to bleed the line. I first pumped my pedal and used the...
Showing results 1 to 9 of 9

 
Forum Jump

All times are GMT -5. The time now is 08:07 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC