Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 250
Search took 0.36 seconds.
Search: Keyword(s): ; Posts Made By: RUBI 4 MY MRS
Forum: TJ Tech Forum 09-16-2014, 01:19 AM
Replies: 19
Views: 450
Posted By RUBI 4 MY MRS
If taking the bulb out & putting it back in...

If taking the bulb out & putting it back in “fixes” it (temporarily) then either there is some corrosion in the socket (or on the bulb) causing a bad connection there or the bulb’s filament is broken...
Forum: TJ Tech Forum 09-16-2014, 01:11 AM
Replies: 8
Views: 149
Posted By RUBI 4 MY MRS
It is not the fuses; it is power (or lack of) TO...

It is not the fuses; it is power (or lack of) TO the fuses. That power comes from the ignition switch. If you have no power TO any of the 3 noted above with the key on, your ignition switch is almost...
Forum: TJ Tech Forum 09-14-2014, 01:47 PM
Replies: 1
Views: 86
Posted By RUBI 4 MY MRS
First thing I would do is put a meter on the...

First thing I would do is put a meter on the battery/alternator when this is happening & see if the voltage is really dropping or not. Possible the gauge is but the charging system is OK.
Forum: TJ Tech Forum 09-14-2014, 01:43 PM
Replies: 9
Views: 336
Posted By RUBI 4 MY MRS
Butros, I see you have 2000. Here is a link to a...

Butros, I see you have 2000. Here is a link to a complete troubleshooting procedure.

http://www.wranglerforum.com/f210/heater-problems-443657.html#post7542633
Forum: TJ Tech Forum 09-14-2014, 01:08 AM
Replies: 8
Views: 149
Posted By RUBI 4 MY MRS
The same contacts in the ignition switch power...

The same contacts in the ignition switch power all 3 things that are not working through the fuse block behind the glove box (fuses 13, 14, 15). If you lose all 3 it is almost certain the switch is...
Forum: TJ Tech Forum 09-09-2014, 11:56 PM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
Here are the pinouts for the fuel pump module...

Here are the pinouts for the fuel pump module connector from my FSM
Forum: TJ Tech Forum 09-09-2014, 04:11 PM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
Assuming you have it wired up correctly. Any...

Assuming you have it wired up correctly. Any chance you got the orange/red wire (pin4) & the black (pin1) one reversed?
Forum: TJ Tech Forum 09-09-2014, 12:36 PM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
There is a reason that the circuit is set up...

There is a reason that the circuit is set up through the PCM such that when the key is on if the PCM does not get a crank sensor signal in about 2-3 seconds it will turn the pump off (disengage the...
Forum: TJ Tech Forum 09-09-2014, 12:21 PM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
Are you sure you had 30 & 87? They should be...

Are you sure you had 30 & 87? They should be across from each other. If you get 85 (30 to 85), I think it is you may be energizing the ASD relay which also means possibly fuse 12 in the fuse block...
Forum: TJ Tech Forum 09-09-2014, 11:32 AM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
I’m not sure about some of your terminology. When...

I’m not sure about some of your terminology. When you bypass the relay you are putting 12v power to the fuel pump wire which should be the orange/red wire? When you do what do you mean by priming, do...
Forum: TJ Tech Forum 09-09-2014, 12:50 AM
Replies: 15
Views: 222
Posted By RUBI 4 MY MRS
When he bypassed the relay & it primed, did it...

When he bypassed the relay & it primed, did it start?



If the wiring to the pump got damaged have you checked fuse 23 in the PDC?
Forum: TJ Tech Forum 09-07-2014, 06:08 PM
Replies: 1
Views: 73
Posted By RUBI 4 MY MRS
Those are not wires, they are vacuum hoses. ...

Those are not wires, they are vacuum hoses.

I can't tell from the photo but are there letters on the back of the control switch? If so here is how they should go.

B = Yellow
C = Brown
...
Forum: TJ Tech Forum 09-06-2014, 12:28 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
Glad to help, I learned something too.

Glad to help, I learned something too.
Forum: TJ Tech Forum 09-06-2014, 12:11 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
So it was related to the clutch job after all! I...

So it was related to the clutch job after all! I see that the TC switch grounds through the same wire as the PCM & a bunch of other things, all through various splices, but surprised that one of them...
Forum: TJ Tech Forum 09-05-2014, 11:55 AM
Replies: 4
Views: 118
Posted By RUBI 4 MY MRS
Good chance it’s a broken actuator pin that...

Good chance it’s a broken actuator pin that connects the ignition switch to the key cylinder. Check this link.

http://www.wranglerforum.com/f210/04-rubicon-wont-start-877057.html#post13166297
Forum: TJ Tech Forum 09-04-2014, 10:10 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
Yes, you checked the grounds the right way. ...

Yes, you checked the grounds the right way.



Pin 4 probably won’t be grounded unless the connector is plugged in & pins 31 & 32 are grounded. It is also possible you won’t get 5v from the 2...
Forum: TJ Tech Forum 09-04-2014, 08:57 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
Well, not your mistake, I mistyped it should in...

Well, not your mistake, I mistyped it should in fact be (-) to those 2 pins to check. The crank sensor grounds through the PCM so that must be grounded. It also needs 5v from the PCM & Then sends a...
Forum: TJ Tech Forum 09-04-2014, 08:16 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
I think those 2 wires ground to the stud on the...

I think those 2 wires ground to the stud on the engine near the oil filter & OP sensor.

Make sure you use the continuity check & use the (+) battery post for the ground.
Forum: TJ Tech Forum 09-04-2014, 07:47 PM
Replies: 32
Views: 2,658
Posted By RUBI 4 MY MRS
That will get the power wire to the ASD & fuel...

That will get the power wire to the ASD & fuel pump relays as well as to the PCM, I think, which is for using the relay in that write up. If you need the ASD relay ground wire for the method in post...
Forum: TJ Tech Forum 09-04-2014, 07:27 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
OK good that you have power to the PCM. I would...

OK good that you have power to the PCM. I would like to see 12v at pin 2 but that may be a bad connection, you might try that one again. Now check pins 31 & 32 for ground. Then plug the connector in...
Forum: TJ Tech Forum 09-04-2014, 12:24 PM
Replies: 32
Views: 2,658
Posted By RUBI 4 MY MRS
From my ’05 FSM & I think your ’06 is the same....

From my ’05 FSM & I think your ’06 is the same. The ground wire for the ASD is a brown/white wire that goes from the relay socket in the PDC to the PCM. You can access it at the socket by lifting the...
Forum: TJ Tech Forum 09-03-2014, 09:45 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
So do you have power to the PCM from fuse 12? You...

So do you have power to the PCM from fuse 12? You certainly should get power from fuse 9 so how far does that have power on its way to pin 22?
Forum: TJ Tech Forum 09-03-2014, 08:23 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
The dark blue wire comes into the PDC & I think...

The dark blue wire comes into the PDC & I think goes first to the FP relay& there it is crimped to a second wire, same color, which goes to the ASD relay & again is double crimped & that wire goes...
Forum: TJ Tech Forum 09-03-2014, 08:08 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
It shouldn’t matter for voltage check. Probably...

It shouldn’t matter for voltage check. Probably easier & more certain if the pins are checked with it unplugged so you don’t have to back probe the terminals where it is harder it be sure you get...
Forum: TJ Tech Forum 09-03-2014, 07:16 PM
Replies: 63
Views: 1,028
Posted By RUBI 4 MY MRS
If both fuses are good & you are sure neither pin...

If both fuses are good & you are sure neither pin has power (key on for fuse12) then lift the PDC & look for broken or corroded wire under there. The ones to check are a dark blue one (from fuse 12)...
Showing results 1 to 25 of 250

 
Forum Jump

All times are GMT -5. The time now is 10:53 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC