Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 32
Search took 0.31 seconds.
Search: Keyword(s): ; Posts Made By: ANOTHER JEEP
Forum: TJ Tech Forum 08-08-2014, 07:53 PM
Replies: 4
Views: 221
Posted By ANOTHER JEEP
Any suggestions as to what is bent / damaged....

Any suggestions as to what is bent / damaged. Since the toe didn't move / change I am guessing that that tie rod and drag link aren't bent. Where should I look next????
ANy suggestions are welcome.
Forum: TJ Tech Forum 08-08-2014, 09:50 AM
Replies: 4
Views: 221
Posted By ANOTHER JEEP
Steering off center

Question: 2005 Jeep Wrangler LJ Rubicon
After a hard weekend of rocks in Pa. the steering wheel is off center, about 20 degrees.
I have Currie steering linkage and the toe hasn't changed. It's...
Forum: TJ Tech Forum 04-06-2014, 09:00 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Thanks for the update. Good pics also. I'm ...

Thanks for the update. Good pics also.
I'm considering getting the BD mounts. I'm just not sure how I want ot go about it.
I now have stock type mounts with JKS 1" blocks and then I have another...
Forum: TJ Tech Forum 03-10-2014, 08:49 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Have fun in Kentucky. What is the event in...

Have fun in Kentucky. What is the event in Kentucky?
Wish I had a plasma cutter.
I actually measured how much lift My MM had yesterday and I lied to you. I actually have 2"s of lift. I have the JKS...
Forum: TJ Tech Forum 03-09-2014, 11:16 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
The iinfo I've received from the 2 of you has...

The iinfo I've received from the 2 of you has been appreciated.

I'd would of never heard of BD MMs if not for you.
I'm going to get the 1 1/2" mounts and maybe the right side bracket. That's...
Forum: TJ Tech Forum 03-08-2014, 06:28 PM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Do you have just the mount or do you have the...

Do you have just the mount or do you have the motor side brackets to go with the mount itself?
I also want to apologize for my lack of knowledge and not checking before speaking. I looked at and...
Forum: TJ Tech Forum 03-08-2014, 11:54 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
I'm jealous also. Looks like a well equipped...

I'm jealous also. Looks like a well equipped shop. I can't get in my 2 car garage. It's full of parts and tools. Hope to expand to a 6 car garage with lift someday. I've also considered a pole bldg....
Forum: TJ Tech Forum 03-08-2014, 12:28 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
I have found that finding a true level pad...

I have found that finding a true level pad [place] that is large enough for a vehicle is really really hard to find. That's why I said that my readings are only relative to see the amount of change...
Forum: TJ Tech Forum 03-07-2014, 12:37 PM
Replies: 28
Views: 6,310
Posted By ANOTHER JEEP
Thanks for the diagram. Easy to understand. So...

Thanks for the diagram. Easy to understand.
So if the front diff is square to the frame and the thrust angle is 0* then all is square.
Am I correct??
Forum: TJ Tech Forum 03-07-2014, 11:31 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
I appreciate your concern. I won't swear that...

I appreciate your concern.
I won't swear that my driveway is level. It is not quite level, but it is concrete and I put the Jeep in the same place to make all my measurements. All my measurements...
Forum: TJ Tech Forum 03-07-2014, 11:05 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Driveshaft pinion angle is measured on the...

Driveshaft pinion angle is measured on the driveshaft and then the angle on the pinion U joint. Subtract one from the other. Digital angle meter is used. I really like it.
Forum: TJ Tech Forum 03-07-2014, 11:01 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Yes, I took the 2 1/2* caster at the front end...

Yes, I took the 2 1/2* caster at the front end alignment as a base.
I then measured the diff angle on the flats on the back of the diff.
It was 96* with 0* pinion angle and 2 1/2* caster.
When I...
Forum: TJ Tech Forum 03-07-2014, 10:29 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Thanks I started at 0* pinion angle, 2 1/2*...

Thanks
I started at 0* pinion angle, 2 1/2* caster.
I was under the impression that any negative [low] pinion angle was unacceptable.
I'm now being told that up to about 3* is OK.
When I went to...
Forum: TJ Tech Forum 03-05-2014, 08:00 PM
Replies: 28
Views: 6,310
Posted By ANOTHER JEEP
Why not just get your thrust angle front and rear...

Why not just get your thrust angle front and rear when you get alignment to check toe and caster?
Does not thrust angle tell you if the front diff is square to the rear diff?
I would agree that it...
Forum: TJ Tech Forum 03-05-2014, 07:10 PM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
I have a high pinion ProRock 44 from Dynatrac. ...

I have a high pinion ProRock 44 from Dynatrac.
I assume that I just have too much lift.
I have RE 3 1/2 springs that I believe give me 4 1/2" lift.
The motor and T case are also up almost 2".
It...
Forum: TJ Tech Forum 03-03-2014, 12:45 AM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
At what speeds should I expect to feel the...

At what speeds should I expect to feel the driveline vibrations?
Forum: TJ Tech Forum 03-02-2014, 11:56 PM
Replies: 29
Views: 1,141
Posted By ANOTHER JEEP
Caster versus Pinion Angle

I realize this topic has been worn out.
I do have a question though.
With "0" pinion angle, I have 2 1/2* of caster.
Should I sacrifice pinion angle to achieve 4 1/2* of caster.
Or should I...
Forum: TJ General Discussion Forum 09-30-2013, 06:56 PM
Replies: 5
Views: 569
Posted By ANOTHER JEEP
My brother has auto repair shop and will assist...

My brother has auto repair shop and will assist with install.
I want to know what issues to expect.
Forum: TJ General Discussion Forum 09-30-2013, 06:53 PM
Replies: 5
Views: 569
Posted By ANOTHER JEEP
To answer both of you. Yes, it came with...

To answer both of you.
Yes, it came with factory air locker.
Broke the front locker and am replacing it with Pro Rock 44 w/ ARB.
Want Detroit Locker in the rear.

Yes, I have a street/strip...
Forum: TJ General Discussion Forum 09-30-2013, 04:58 PM
Replies: 5
Views: 569
Posted By ANOTHER JEEP
Detroit Locker

I want to put a Detroit locker in the rear of my 2005 Jeep Wrangler Unlimited Rubicon.
I called Eaton today and they said that it is not a direct replacement in the TJ Rubicon.
They said to use the...
Forum: TJ Tech Forum 08-28-2013, 06:28 PM
Replies: 25
Views: 5,098
Posted By ANOTHER JEEP
body lift

Get a 1 to 1 1/2 inch body lift. It gives you extra clearance to work on the vehicle. With 1 1/2" you can get between the frame and the body.
If you get a 1" motor lift with a 1" body lift the fan...
Forum: TJ Tech Forum 06-15-2013, 12:36 PM
Replies: 1
Views: 437
Posted By ANOTHER JEEP
Differential skid plates

After offroading last weekend on some pretty rocky trails both the front and rear diffs were well scrapped up. Should I worry about this and if so what options do I have for skid plates. There are...
Forum: Trail Pics 06-14-2013, 09:23 AM
Replies: 4
Views: 1,542
Posted By ANOTHER JEEP
Where is this???? Who gets to clean the mud...

Where is this????
Who gets to clean the mud off?
How do you clean the undercarriage so that next year when you take a bolt out you don't get a face full of DIRT ???
Good pics, Looks like you had...
Forum: TJ General Discussion Forum 06-14-2013, 09:19 AM
Replies: 49
Views: 10,136
Posted By ANOTHER JEEP
Great idea. Thanks for sharing it. I will have to...

Great idea. Thanks for sharing it. I will have to measure to see if it will fit in the back of my LJ with the rear seat in. I have to take the grand kids on the trail with me and need the rear...
Forum: TJ General Discussion Forum 04-05-2013, 11:14 PM
Replies: 9
Views: 593
Posted By ANOTHER JEEP
Currie is really a good kit All I need is the...

Currie is really a good kit
All I need is the springs and shocks
I've already pieced the rest together.
Showing results 1 to 25 of 32

 
Forum Jump

All times are GMT -5. The time now is 01:40 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC