Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 72
Search took 0.30 seconds.
Search: Keyword(s): ; Posts Made By: dukes-o-hazard
Forum: YJ Tech Forum 04-03-2014, 09:43 PM
Replies: 7
Views: 375
Posted By dukes-o-hazard
Thinking about going chrysler 8.25 w/ XJ spring...

Thinking about going chrysler 8.25 w/ XJ spring in the rear and maybe a spring conversion w/ dana 44 up front. So, i should be able to gain 10-12" total with that set up, w/o doing anything too crazy...
Forum: YJ Tech Forum 04-01-2014, 01:23 AM
Replies: 7
Views: 375
Posted By dukes-o-hazard
4" SUA Lift w/ 6" stretch to fit 37's

I was wondering if anyone sells 4 inch lifts that will also stretch my well base 6 in the front and 6 out back, I am not afraid to trim to achieve desired results.
Forum: Builders Corner 11-01-2013, 10:44 PM
Replies: 2
Views: 530
Posted By dukes-o-hazard
Diamond plate damage control install

Very affordable, very simple, diamond plate damage control Welcome to Jeepdiamondplate.com We have the best prices on Jeep body armor (http://www.jeepdiamondplate.com)

I purchased a few sheets of...
Forum: YJ Tech Forum 08-04-2013, 02:11 AM
Replies: 88
Views: 3,335
Posted By dukes-o-hazard
50/50 mix of synthetic and non-syn Lucas oil 10w...

50/50 mix of synthetic and non-syn Lucas oil 10w 30, STP filter..btw STP internals are the same as the $13 K&N wrench off's.
Forum: YJ Tech Forum 08-01-2013, 01:51 AM
Replies: 2
Views: 232
Posted By dukes-o-hazard
Does it have the electric choke? Also, you could...

Does it have the electric choke? Also, you could try adjusting the settings http://www.redlineweber.com/html/Tech/38_dgas_tunning.htm
Forum: YJ Tech Forum 08-01-2013, 01:40 AM
Replies: 2
Views: 308
Posted By dukes-o-hazard
Check your fuse block...

Check your fuse block...
Forum: YJ Tech Forum 08-01-2013, 01:35 AM
Replies: 2
Views: 192
Posted By dukes-o-hazard
Psst..go with Lucas, haha..You'll get ten...

Psst..go with Lucas, haha..You'll get ten different answers from ten different people, but I personally stick with Lucas.
Forum: YJ Tech Forum 08-01-2013, 01:30 AM
Replies: 9
Views: 509
Posted By dukes-o-hazard
Nice pics, I like the carnage the rod end did to...

Nice pics, I like the carnage the rod end did to the block, seems common for this engine. My couins did the same thing to him, except his went out the oil pan. I will be picking it up in a couple...
Forum: YJ Tech Forum 08-01-2013, 01:22 AM
Replies: 9
Views: 417
Posted By dukes-o-hazard
You should do a compression test first.

You should do a compression test first.
Forum: YJ Tech Forum 07-24-2013, 01:33 PM
Replies: 10
Views: 433
Posted By dukes-o-hazard
Yes, but the torque converter cost $300 just by...

Yes, but the torque converter cost $300 just by itself, I'm actually thinking about buying the rebuild kit and doing it my self..Know of anyone who has tackled this?
Forum: YJ Tech Forum 07-23-2013, 11:54 PM
Replies: 10
Views: 433
Posted By dukes-o-hazard
Yeah, same here, I'm only finding the master...

Yeah, same here, I'm only finding the master rebuild kits at that cost.
Forum: YJ General Discussion Forum 07-22-2013, 12:14 AM
Replies: 22
Views: 6,770
Posted By dukes-o-hazard
I was thinking about doing this just for a...

I was thinking about doing this just for a different look, haha..looks like we might have to start a new monstalined jeep thread!
Forum: YJ Tech Forum 07-21-2013, 10:59 PM
Replies: 5
Views: 611
Posted By dukes-o-hazard
There are a couple of different kits, I've had it...

There are a couple of different kits, I've had it on the back burner since my first jeep.
CJ Tailgate Conversion Kit for your TJ or YJ...
Forum: YJ Tech Forum 07-21-2013, 05:35 PM
Replies: 5
Views: 611
Posted By dukes-o-hazard
I think this mod is a must for the guys out there...

I think this mod is a must for the guys out there running the truck tops.
Forum: Builders Corner 07-21-2013, 05:32 PM
Replies: 3
Views: 614
Posted By dukes-o-hazard
Nice, I like the idea of gaining wheel clearance...

Nice, I like the idea of gaining wheel clearance with out lifting it. I will be taking mine off when I roll it w/ the bedliner stuff, then I might just leave em off.
Forum: YJ Tech Forum 07-21-2013, 04:53 AM
Replies: 9
Views: 332
Posted By dukes-o-hazard
Sounds like a bad ground to me..so, the pump runs...

Sounds like a bad ground to me..so, the pump runs on 12v?
Forum: YJ Tech Forum 07-21-2013, 04:39 AM
Replies: 2
Views: 349
Posted By dukes-o-hazard
Sounds like it might be a good time to go to the...

Sounds like it might be a good time to go to the local salvage and get a used one. You can probably pick one up for the cost of a master rebuild kit and that would be you doing the rebuild. If it...
Forum: YJ Tech Forum 07-21-2013, 04:32 AM
Replies: 3
Views: 236
Posted By dukes-o-hazard
I can see them moving a little bit more air then...

I can see them moving a little bit more air then factory, but if your looking for more cooling perhaps a bigger radiator is the answer. I'm actually looking into going electric to loose the parasitic...
Forum: YJ Tech Forum 07-21-2013, 02:50 AM
Replies: 20
Views: 751
Posted By dukes-o-hazard
Yes, I agree with POS, but also with everyone...

Yes, I agree with POS, but also with everyone else on here. If your going to modify your steering then you should 1.) Go bigger/stronger and 2.) Flip it to the top giving you clearance that is good...
Forum: YJ Tech Forum 07-21-2013, 02:26 AM
Replies: 3
Views: 285
Posted By dukes-o-hazard
Yeap, no go, mechanically I think it would drop...

Yeap, no go, mechanically I think it would drop right in..But the you'd have to go hacking the electrical side of it and your bro prolly wouldn't find that very amusing..haha, Yes, do a compression...
Forum: YJ Tech Forum 07-21-2013, 12:00 AM
Replies: 1
Views: 272
Posted By dukes-o-hazard
Short answer, none, there both totally...

Short answer, none, there both totally interchangeable.
Forum: YJ Tech Forum 07-20-2013, 11:55 PM
Replies: 10
Views: 904
Posted By dukes-o-hazard
If you checked all the u joints and your sure...

If you checked all the u joints and your sure there good, then I would venture to say that it's probably coming from your rear ring and pinion not meshing properly. You might get lucky and it may be...
Forum: YJ Tech Forum 07-20-2013, 11:44 PM
Replies: 12
Views: 445
Posted By dukes-o-hazard
http://www.wranglerforum.com/f5/grinding-into-reve...

http://www.wranglerforum.com/f5/grinding-into-reverse-90550.html
Forum: YJ Tech Forum 07-20-2013, 11:40 PM
Replies: 2
Views: 227
Posted By dukes-o-hazard
Are the door switches operable?

Are the door switches operable?
Forum: YJ Tech Forum 07-20-2013, 11:37 PM
Replies: 3
Views: 285
Posted By dukes-o-hazard
The part numbers do not cross, I think it more of...

The part numbers do not cross, I think it more of and electrical issue, than a mechanical one. Have you done a compression test? Sounds like that might be the issue, how many miles on the jeep? Also,...
Showing results 1 to 25 of 72

 
Forum Jump

All times are GMT -5. The time now is 02:18 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC