Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 250
Search took 0.21 seconds.
Search: Keyword(s): ; Posts Made By: RUBI 4 MY MRS
Forum: TJ Tech Forum 03-27-2015, 11:31 PM
Replies: 6
Views: 152
Posted By RUBI 4 MY MRS
When either of the front signals including the...

When either of the front signals including the markers acts differently when the lights are on the problem is almost always in the bulbs, sockets or wiring in the front on that side. This includes...
Forum: TJ Tech Forum 03-27-2015, 06:28 PM
Replies: 12
Views: 307
Posted By RUBI 4 MY MRS
Your answer to this is almost certainly in the...

Your answer to this is almost certainly in the link in your 1st post here. And the answer to your very 1st question is YES (& jkp above it right, too). I have seen many P0016 postings & properly...
Forum: TJ Tech Forum 03-25-2015, 04:49 PM
Replies: 1
Views: 108
Posted By RUBI 4 MY MRS
Understanding that all the power goes through the...

Understanding that all the power goes through the switch if you just want to bypass the OEM one & install a separate switch somewhere but still use the factory wiring as much as possible you can go...
Forum: TJ Tech Forum 03-19-2015, 09:50 PM
Replies: 10
Views: 179
Posted By RUBI 4 MY MRS
OK somewhere between the fan switch & the...

OK somewhere between the fan switch & the resistor the tan wire is shorting to the brown/tan wire causing a bypass of the resistor & closing the high speed contacts in the relay. The tan wire also...
Forum: TJ Tech Forum 03-19-2015, 07:33 PM
Replies: 10
Views: 179
Posted By RUBI 4 MY MRS
2 questions. Does the fan turn off when you slide...

2 questions. Does the fan turn off when you slide the mode selector to the off position? If no, does it shut off when the key is off?
Forum: TJ Tech Forum 03-14-2015, 12:08 AM
Replies: 4
Views: 225
Posted By RUBI 4 MY MRS
If you are getting key on power but no constant...

If you are getting key on power but no constant 12v power to the relay through the red/white wire you need to recheck fuse 9 in the PDC. If good check the wire, it goes from the fuse to the relay &...
Forum: TJ Tech Forum 03-13-2015, 10:41 PM
Replies: 4
Views: 225
Posted By RUBI 4 MY MRS
Which wire is getting power? One (dark blue)...

Which wire is getting power? One (dark blue) should get power when the key is on. The other (red/white) should have power all the time.
Forum: TJ Tech Forum 03-12-2015, 11:18 PM
Replies: 30
Views: 614
Posted By RUBI 4 MY MRS
I haven't had to try this but have read it works...

I haven't had to try this but have read it works well. If you get it post how it works.

External Regulator Conversion Kit for Jeep.

External Voltage Regulator Kit for Chrysler Dodge Jeep,...
Forum: TJ Tech Forum 03-12-2015, 06:39 PM
Replies: 3
Views: 161
Posted By RUBI 4 MY MRS
Make sure you have 2 12v inputs to the headlight...

Make sure you have 2 12v inputs to the headlight switch (not the dimmer switch). You may be missing power to the tan/black wire (pin 4) from fuse 1 in the fuse block behind the glove box. Even if the...
Forum: TJ Tech Forum 03-12-2015, 06:11 PM
Replies: 59
Views: 1,840
Posted By RUBI 4 MY MRS
The drilling you saw was probably from those of...

The drilling you saw was probably from those of us that did mods to get grease or oil to the top bushing on the OEM units before the Dorman & Crown units became available. Those mods go back to at...
Forum: TJ Tech Forum 03-09-2015, 06:24 PM
Replies: 2
Views: 76
Posted By RUBI 4 MY MRS
The PCM sends data to the cluster so the sender...

The PCM sends data to the cluster so the sender may be good & the pressure may also be good, just the PCM sending bad data to the gauge, or... not. The only way to know what the actual pressure is is...
Forum: TJ Tech Forum 03-09-2015, 12:40 PM
Replies: 6
Views: 324
Posted By RUBI 4 MY MRS
I have a 2005 so mine is different but according...

I have a 2005 so mine is different but according to the ’99 FSM you have to move the PCM out of the way but it sounds like you don’t have to unplug the 3 connectors.

BLOWER MOTOR
REMOVAL...
Forum: TJ Tech Forum 03-06-2015, 11:19 PM
Replies: 6
Views: 324
Posted By RUBI 4 MY MRS
As Water Dog says there is the diagnostic...

As Water Dog says there is the diagnostic procedure there but when it is intermittent there may not be constant power to the motor which is the 1st check of the procedure. Here are some examples of...
Forum: TJ Tech Forum 03-06-2015, 12:20 PM
Replies: 2
Views: 130
Posted By RUBI 4 MY MRS
Speed 4 (high) bypasses the resistor. If you are...

Speed 4 (high) bypasses the resistor. If you are getting speeds 1-3 but no 4 then either fuse 11 in the PDC is bad or the relay is not closing. That relay is up near the resistor under the dash on...
Forum: TJ Tech Forum 03-02-2015, 12:11 AM
Replies: 6
Views: 183
Posted By RUBI 4 MY MRS
The only 2 wires I can think of from the PCM to...

The only 2 wires I can think of from the PCM to the auto trans would be (1) an orange/light green wire from pin B-11 of the C-2 (white) PCM connector for the torque converter lockup solenoid. Then a...
Forum: TJ Tech Forum 02-19-2015, 01:27 AM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
Well, I misunderstood you. When you said you were...

Well, I misunderstood you. When you said you were replacing the key cylinder I assumed you had already done the actuator assembly & for some reason decided to do the cylinder too. But for the broken...
Forum: TJ Tech Forum 02-18-2015, 10:45 PM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
I don’t see where it says anything about needing...

I don’t see where it says anything about needing a programmed key. The programmed key is the grey key for SKIM equipped jeeps. If you have the black (non-SKIM) key it doesn’t matter. If you have a...
Forum: TJ Tech Forum 02-18-2015, 09:46 PM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
No, get this kit that you match to your existing...

No, get this kit that you match to your existing key.

Ignition Key Lock Cylinder repair kit

Dorman Ignition Key Lock Cylinders 924-703

Replaces OEM Part Number: Chrysler 5083915AB
...
Forum: TJ Tech Forum 02-18-2015, 06:11 PM
Replies: 26
Views: 9,367
Posted By RUBI 4 MY MRS
Here is a link to a u-tube video on replacing the...

Here is a link to a u-tube video on replacing the actuator assembly which also involves removing the ignition switch. However you can replace the switch without removing the actuator by removing the...
Forum: TJ Tech Forum 02-18-2015, 03:22 PM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
Did it fix the radio too?

Did it fix the radio too?
Forum: TJ Tech Forum 02-17-2015, 09:46 PM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
You can’t test the yellow wire that way. The only...

You can’t test the yellow wire that way. The only way it will get power (12v) is if the connector is connected to the switch. Then when you turn the switch to the start position power from the red...
Forum: TJ Tech Forum 02-17-2015, 06:39 PM
Replies: 24
Views: 401
Posted By RUBI 4 MY MRS
If you get nothing from the yellow wire it could...

If you get nothing from the yellow wire it could be the ignition switch but more likely the tip of the actuator assembly is broken. Pull the switch from the actuator & see if the tip is broken, a...
Forum: TJ Tech Forum 02-16-2015, 11:06 PM
Replies: 26
Views: 9,367
Posted By RUBI 4 MY MRS
The wipers, signals & radio all get power to...

The wipers, signals & radio all get power to their fuses from the same wire (power source) coming from the ignition witch. If you lose all 3 at the same time it is almost for sure a bad switch....
Forum: TJ Tech Forum 02-16-2015, 01:02 PM
Replies: 2
Views: 128
Posted By RUBI 4 MY MRS
Those look like connectors C-103 & C-104. Both...

Those look like connectors C-103 & C-104. Both are on the firewall near the back of the engine, as you can see from the diagrams above. The one with the 4 open or blank slots would be C-104. The open...
Forum: TJ Tech Forum 02-15-2015, 06:47 PM
Replies: 8
Views: 350
Posted By RUBI 4 MY MRS
You can replace the switch without removing the...

You can replace the switch without removing the key cylinder & actuator assembly. Remove the plastic column covers. There is 1 Torx security bolt that holds the ignition switch to the actuator...
Showing results 1 to 25 of 250

 
Forum Jump

All times are GMT -5. The time now is 06:45 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC