Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 248
Search took 0.21 seconds.
Search: Keyword(s): ; Posts Made By: DirtyRob
Forum: YJ Tech Forum 11-19-2014, 08:04 PM
Replies: 5
Views: 273
Posted By DirtyRob
A little more info on your engine type year etc...

A little more info on your engine type year etc would help out a bit, but generically I would have to agree with the above post, and also say that it a bad ground can really get you running in...
Forum: YJ Tech Forum 11-19-2014, 07:58 PM
Replies: 3
Views: 261
Posted By DirtyRob
It sounds like a fuel pressure regulator problem...

It sounds like a fuel pressure regulator problem or maybe a dirty fuel filter

X2 on checking the fuel pressure
Forum: YJ Tech Forum 11-19-2014, 07:56 PM
Replies: 5
Views: 337
Posted By DirtyRob
That sounds like a good plan

That sounds like a good plan
Forum: YJ Tech Forum 11-19-2014, 07:47 PM
Replies: 16
Views: 1,305
Posted By DirtyRob
A good pair of vise grips usually does the trick,...

A good pair of vise grips usually does the trick, if not, I weld a 1/2" nut to the head, and it will come right out.

To adjust the windshield after angle right to fit, the easiest way I have...
Forum: YJ Tech Forum 11-19-2014, 07:35 PM
Replies: 2
Views: 192
Posted By DirtyRob
Not really enough info, but it sounds like maybe...

Not really enough info, but it sounds like maybe a brake may be hanging among a lot of other things that could case it to feel like it is dragging.
My 2.5 always felt like that in 5th gear unless...
Forum: YJ Tech Forum 11-19-2014, 07:30 PM
Replies: 4
Views: 284
Posted By DirtyRob
I sheared my tranny mount bolts off under the...

I sheared my tranny mount bolts off under the skid plate a few times climbing rocks. You can order a new one from Quadratec the easiest. I got one from e-bay, and waited longer for it. Since then I...
Forum: YJ Tech Forum 11-19-2014, 07:26 PM
Replies: 15
Views: 410
Posted By DirtyRob
It looks to me like a 2 1/2-4" lift. Most decent...

It looks to me like a 2 1/2-4" lift. Most decent 2 1/2" lifts net 3+ inches, and 4" lifts tend to be 4 1/2 or so until the springs get used a bit. As far a having a body lift, the rubber grommets...
Forum: YJ Tech Forum 11-12-2014, 08:43 PM
Replies: 8
Views: 324
Posted By DirtyRob
I chose the Zone 2" and went spring over axle....

I chose the Zone 2" and went spring over axle. The Zone springs ride great
Forum: YJ Tech Forum 11-09-2014, 10:04 PM
Replies: 39
Views: 1,306
Posted By DirtyRob
If you want to keep 31's and a 2.5, and do not...

If you want to keep 31's and a 2.5, and do not mind spending the money to do it right the first time, I would go with a Ford 8.8 with disk brakes in the rear and not spend anything on the Dana 35,...
Forum: YJ Tech Forum 11-09-2014, 09:45 PM
Replies: 10
Views: 324
Posted By DirtyRob
I haven't got my rear driveshaft ordered as of...

I haven't got my rear driveshaft ordered as of yet, so I cannot tell how it will do everyday yet, but Adams Driveshaft will be building me one after I call them tomorrow. They are the ones I always...
Forum: YJ Tech Forum 11-09-2014, 09:40 PM
Replies: 8
Views: 324
Posted By DirtyRob
I had 4.88's under my 2.5 and was still a junk a...

I had 4.88's under my 2.5 and was still a junk a motor for anything but wheeling.
I am almost done swapping in a Mopar 360 v-8, 8 lug axles, NP435 and now I can actually use it

To the OP, The...
Forum: YJ Tech Forum 11-06-2014, 10:34 PM
Replies: 10
Views: 324
Posted By DirtyRob
I plumbed in the hard line tonight and bled the...

I plumbed in the hard line tonight and bled the slave cylinder. The clutch seems to work great. I need to get the drive shafts built and then I will report back.
Forum: YJ Tech Forum 11-05-2014, 10:27 PM
Replies: 10
Views: 324
Posted By DirtyRob
I still have to get the hard line with the...

I still have to get the hard line with the correct ends to try it out, but I found that a 1983 CJ5 4 cylinder slave cylinder fits the Dodge bell housing with a little grinding. It seems to have the...
Forum: YJ Tech Forum 11-05-2014, 12:51 PM
Replies: 10
Views: 324
Posted By DirtyRob
I know the they have to match due to bore size...

I know the they have to match due to bore size for correct throw, the dodge master will not fit on the fire wall. I was hoping someone knew where I could get info on bore sizes etc.

I think I may...
Forum: YJ Tech Forum 11-05-2014, 11:12 AM
Replies: 10
Views: 324
Posted By DirtyRob
The problem is the lack of room at the brake...

The problem is the lack of room at the brake booster. The stock YJ master cylinder barely fits
Forum: YJ Tech Forum 11-04-2014, 08:34 PM
Replies: 10
Views: 324
Posted By DirtyRob
Ok. My 1990 YJ Wrangler started life as a 2.5 TBI...

Ok. My 1990 YJ Wrangler started life as a 2.5 TBI 4 cylinder. I came across a deal to buy a 1989 Dodge Ramcharger with a TBI 360 V-8, NP435 4 speed tranny (granny gear) and NP241 xfer case with 14...
Forum: YJ Tech Forum 11-04-2014, 06:55 AM
Replies: 10
Views: 324
Posted By DirtyRob
dodge 360 and MP435 in 1990 YJ clutch issues

I am running into a dead end on getting the clutch info I need to get this done. Anyone ever do this swap? The stock master cylinder for the clutch fits behind the brake booster, but the dodge will...
Forum: Jeep Part-Outs 09-29-2014, 08:22 PM
Replies: 7
Views: 495
Posted By DirtyRob
I do have a rear seat, but it is not for sale. I...

I do have a rear seat, but it is not for sale. I never had a rear seat for sale, just the drivetrain.
Everything has been sold. Please delete
Forum: Jeep Part-Outs 08-07-2014, 09:56 PM
Replies: 7
Views: 495
Posted By DirtyRob
everything else is still available. I am...

everything else is still available. I am negotiable on the motor and tranny but am asking $800 for the motor which comes complete and ready to bolt in with many new parts including new alternator,...
Forum: Jeep Part-Outs 08-07-2014, 09:55 PM
Replies: 7
Views: 495
Posted By DirtyRob
I sold them with the transfercase and rear...

I sold them with the transfercase and rear driveshaft for $1,500, and installed for $2,000
Forum: Jeep Part-Outs 08-05-2014, 09:43 PM
Replies: 7
Views: 495
Posted By DirtyRob
Dunn NC 28334

Dunn NC 28334
Forum: Jeep Part-Outs 07-28-2014, 09:32 PM
Replies: 7
Views: 495
Posted By DirtyRob
90 YJ complete drivetrain for sale 4.88 gears

I am putting a 360 and 8 lug axles in my 90 YJ. I have everything I do not need for sale.

The motor is a 2.5tbi with 13,000 miles since a complete re-build, and runs great.

Axles are as...
Forum: On The Trail 07-21-2014, 05:45 PM
Replies: 11,271
Views: 385,626
Posted By DirtyRob
I agree. I am in no way a guru or any authority...

I agree. I am in no way a guru or any authority on Jeeps, It is strictly opinion.
I would like to note that My $300 winch is much more valuable than any tire combo. I take my stock XJ (daily...
Forum: On The Trail 07-20-2014, 07:14 PM
Replies: 11,271
Views: 385,626
Posted By DirtyRob
Count me in for the next get together east of...

Count me in for the next get together east of Raleigh.
I do have one question on the pics I keep seeing in this thread.....Why is there so many people that neglect to buy a winch?

I am not...
Forum: YJ Tech Forum 07-15-2014, 07:59 PM
Replies: 82
Views: 19,821
Posted By DirtyRob
12,000 here after a complete re-build. Runs...

12,000 here after a complete re-build. Runs great. It died around 100,000 with regular oil changes according to the previous owner. He said it lost compression in 2 cylinders. Some folks seem to get...
Showing results 1 to 25 of 248

 
Forum Jump

All times are GMT -5. The time now is 04:50 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC