Jeep Wrangler Forum - Search Results
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Search Forums

Join Wrangler Forum Today


Showing results 1 to 25 of 212
Search took 0.37 seconds.
Search: Keyword(s): ; Posts Made By: horsedad58
Forum: TJ Tech Forum 01-28-2014, 04:31 PM
Replies: 8
Views: 465
Posted By horsedad58
Sorry, but I'm stumped. The heater circuit on a...

Sorry, but I'm stumped. The heater circuit on a 2.5 is pretty simple. I don't think there are any valves in the lines to the passenger compartment. Chrysler did put some in other vehicles. So as...
Forum: TJ Tech Forum 01-28-2014, 02:45 PM
Replies: 10
Views: 235
Posted By horsedad58
If someone used a non-vented t-stat in your jeep...

If someone used a non-vented t-stat in your jeep it can get a big air bubble trapped until the engine gets hot enough to cause it to open. The catch is with no coolant up at the housing, the t-stat...
Forum: TJ Tech Forum 01-27-2014, 01:50 PM
Replies: 8
Views: 465
Posted By horsedad58
The diverter door (more properly called the...

The diverter door (more properly called the 'blend door' by Chrysler) is inside the airbox behind the center console and the glove box. The door defaults to the AC-Vent position until a vacuum motor...
Forum: TJ Tech Forum 01-27-2014, 01:18 PM
Replies: 8
Views: 465
Posted By horsedad58
Check the air diverter door operation. If you...

Check the air diverter door operation. If you have hot water in and out as you say, you core is probably good. I'd guess your pneumatic actuator that moves the damper (controls the airflow between...
Forum: Florida Jeep Forum 12-06-2013, 06:04 PM
Replies: 47
Views: 1,512
Posted By horsedad58
Bob, Susan and I will be at CB early for...

Bob, Susan and I will be at CB early for breakfast with the back of the jeep pretty full of toys!!!
Forum: TJ Tech Forum 12-05-2013, 02:24 PM
Replies: 38
Views: 1,196
Posted By horsedad58
I posted a relatively quick way to check SYE...

I posted a relatively quick way to check SYE output yoke run out. Check out the thread titled "another vibration issue." Page 3. (Sorry, I don't know how to embed a link yet..) You do need a ball...
Forum: TJ Tech Forum 12-03-2013, 06:58 PM
Replies: 34
Views: 1,265
Posted By horsedad58
X2 And I might add two other checks, 1,...

X2

And I might add two other checks, 1, check both ends of the track bar for movement while turning the wheels. 2, check the wheel bearings for looseness when turning the wheels.
Forum: TJ Tech Forum 12-03-2013, 03:52 PM
Replies: 27
Views: 939
Posted By horsedad58
OK, here are some staged pictures of how I...

OK, here are some staged pictures of how I measured the concentricity or radial runout of my output yoke. Sharp eyed readers will undoubtedly note that the tail housing I used in these shots is...
Forum: TJ Tech Forum 12-03-2013, 01:17 PM
Replies: 4
Views: 210
Posted By horsedad58
My ACE hardware carries an excellent selection of...

My ACE hardware carries an excellent selection of grade 8 equivalent metric hardware ( I think in metric bolts grade 8 is marked 10.9 ) including metric nyloc nuts. You may want to check there..
Forum: TJ Tech Forum 12-03-2013, 01:01 PM
Replies: 27
Views: 939
Posted By horsedad58
It was a PITA! But i had already bought two, yes...

It was a PITA! But i had already bought two, yes two! new driveshafts as well as adjusted my pinion angles a dozen times. I decided it was time to stop spending $$$$ on " it might be this" and do a...
Forum: TJ Tech Forum 12-03-2013, 12:48 PM
Replies: 27
Views: 939
Posted By horsedad58
Since the output yoke on the transfer case isn't...

Since the output yoke on the transfer case isn't circular you need something bolted to it that will let you measure the concentricity of the yokes rotation.

I got just the ball yoke portion of a...
Forum: TJ Tech Forum 12-03-2013, 09:22 AM
Replies: 34
Views: 1,265
Posted By horsedad58
Welcome.. hope you find your problem and it's...

Welcome.. hope you find your problem and it's cheap to fix!
Forum: TJ Tech Forum 12-03-2013, 09:19 AM
Replies: 27
Views: 939
Posted By horsedad58
Not an all inclusive response but in my recent...

Not an all inclusive response but in my recent experience, an out of balance shaft caused a constant vibration increasing in frequency as speed increased. An off centered output yoke caused two...
Forum: TJ Tech Forum 12-03-2013, 09:02 AM
Replies: 34
Views: 1,265
Posted By horsedad58
Be very careful there.... While I agree that...

Be very careful there.... While I agree that level steering linkage will minimize steering effort for a given steering system, TJ's and dropped pitman arms do not play well together. Since the TJ...
Forum: TJ Tech Forum 12-02-2013, 11:43 AM
Replies: 19
Views: 988
Posted By horsedad58
I had something similar. A vibration that came on...

I had something similar. A vibration that came on around 40 mph and went away around 50 mph but then at 65 mph or so it came back as a rhythmic, pulsing vibration. In my case it turned out to be a...
Forum: TJ Pics Forum 12-02-2013, 09:30 AM
Replies: 234
Views: 18,332
Posted By horsedad58
My 05... 559226

My 05...


559226
Forum: Florida Jeep Forum 11-27-2013, 11:51 AM
Replies: 47
Views: 1,512
Posted By horsedad58
Already have three in a bag on the counter! ...

Already have three in a bag on the counter! Looking to gather some more before the 7th...
Forum: TJ Tech Forum 11-26-2013, 08:33 PM
Replies: 5
Views: 451
Posted By horsedad58
Yeh, they can last but I did a lot of research on...

Yeh, they can last but I did a lot of research on spicers website and in their reference books and they go on about the cyclic loading on single u-joints, especially at higher speeds. There are lots...
Forum: TJ Tech Forum 11-26-2013, 08:10 PM
Replies: 5
Views: 451
Posted By horsedad58
X2. The small u-joints at your steering knuckles...

X2. The small u-joints at your steering knuckles are not designed for continuous high speed use. The front driveshaft can handle it but those steering u-joints can let go under prolonged high speed...
Forum: TJ General Discussion Forum 11-22-2013, 09:27 AM
Replies: 7,567
Views: 491,473
Posted By horsedad58
x2!!!!!!!

x2!!!!!!!
Forum: TJ Tech Forum 11-22-2013, 09:25 AM
Replies: 7
Views: 610
Posted By horsedad58
I use Chevron's Techcron but regardless of brand,...

I use Chevron's Techcron but regardless of brand, they all do "clean" somewhat but at the dilution level of the average fuel tank, its not gonna do miracles. They help with fuel varnishes and some...
Forum: Florida Jeep Forum 11-19-2013, 02:56 PM
Replies: 47
Views: 1,512
Posted By horsedad58
Yeh, yeh... joining the darkside... I know. ...

Yeh, yeh... joining the darkside... I know.

Whatcha gonna do? I drive a black jeep already.
Forum: TJ Tech Forum 11-19-2013, 12:05 PM
Replies: 25
Views: 1,568
Posted By horsedad58
Its a Jeep! Every spec of dirt, every bit...

Its a Jeep!

Every spec of dirt, every bit of tree sap, every glob of mud, every blob of bird crap dreams of being stuck to a jeep...

How else do you explain the multitudes of jeeps so dirty...
Forum: Florida Jeep Forum 11-19-2013, 11:55 AM
Replies: 47
Views: 1,512
Posted By horsedad58
Ok, Bob. I event went so far as to Sign-up for...

Ok, Bob. I event went so far as to Sign-up for Facebook just so I could RSVP ya!
Forum: TJ Tech Forum 11-18-2013, 08:53 PM
Replies: 7
Views: 364
Posted By horsedad58
What part is shot on your intermediate shaft? If...

What part is shot on your intermediate shaft? If it's just the center support bearing, I stumbled on a cheaper fix than replacing it.

I had to replace my upper steering column earlier and the...
Showing results 1 to 25 of 212

 
Forum Jump

All times are GMT -5. The time now is 08:14 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC