R1 CONCEPTS| NEW CARBON ALLOY GEOMET ROTORS & R1, EBC, and HAWK PADS! - Jeep Wrangler Forum
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Vendors > R1 Concepts

Join Wrangler Forum Today


Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 06-02-2017, 08:16 PM
Thread Starter
  #1
Supporting Vendor
 
r1concepts's Avatar
 
Join Date: Oct 2015
Location: Cerritos, CA
Posts: 572
R1 CONCEPTS| NEW CARBON ALLOY GEOMET ROTORS & R1, EBC, and HAWK PADS!

R1 Concepts Inc- New Carbon Alloy Geomet Rotors!
We're excited to introduce to you all our new Carbon Alloy Geomet rotors! These rotors are a new and improved version of our "Premier Series" rotors. Manufactured for European and heavy vehicles, our High Carbon iron formulations enhances noise dampening characteristics, while providing high strength, and increased thermal conductivity compared to standard discs, which increases durability. Each rotor is engineered to match the OE vane configuration, including OE split-core technology to ensure proper and maximum heat dissipation. Additionally, all cores are dipped with a specifically formulated paint in order to provide a smoother finish inside the vane structure. The smooth finish will improve air flow as well as reduce the amount of machining require in or to properly balance the finished rotor during the mill-balancing process.

Fine Turned
Next, the castings are sent to our state of the art machining facilities, where each rotor is machined to the tightest tolerances available in the market today. We can guarantee specifications of .010mm disc thickness variation (DTV) and .050mm maximum lateral runout. Though in practive, we regularly achieve .007mm DTV and .025mm maximum lateral runout. Then, the rotors are fine turned to a maximum of 1.6 RMS. The objective of these strict tolerances is to create the smoothest possible finish, which improves initial break-in due to the increased contact between the pad and the rotor.

After all of the machining processes are completed, each rotor passes a 100% electronic inspection station that measures over 20 attributes to ensure that each rotor meets OE specifications. This further guarantees that each and every rotor delivered to you is trouble free.

GEOMET Finish- The Superior Corrosion
Finally we apply a genuine GEOMET Finish throughout the entire part, which promises to deliver superior corrosion protection. The GEOMET coating is processed dry, shipped dry, and ready to install without any additional preparation. An average brake job takes 1.25-2.5 hours per axle. Without the need to clean an oil covered rotor, this same a tremendous amount of time and money during the installation process.
  • Superior Corrosion Protection- Provides excellent cyclic corrosion performance when tested to automotive manufacture's test methods incorporating heat, salt spray (withstands 400) and humidity.

  • Environmentally friendly, this meets the following regulations: Environmental Protection Agency (EPA), Chrylser CS-9003, General Motors GMW 3059, Ford WSS-M99P9999-A1 (Hex 9), the EU Directives on End of Life Vehicles (ELV) and Electrical Equipment (RoHS).

  • No Toxic Metal: Free of chromium, nickel, cadmium, lead, barium, and mercury




ROTORS
FT/RR CARBON ALLOY GEOMET ROTORS (ANY DRILLING PATTERN): $240 SHIPPED

FRONT CARBON ALLOY GEOMET ROTORS (ANY DRILLING PATTERN): $120 SHIPPED


BRAKE PADS
R1 OPTIMUM CERAMIC PADS
R1 PERFORMANCE SPORT PADS
ALL HAWK PADS
ALL EBC PADS


BRAKE FLUID
ATE TYPE 200 BRAKE FLUID (1L)
TOTAL: $12/BOTTLE

__________________
Kevin- Sales Representative
R1 Concepts Inc. - Performance Brake Parts
888-712-6623 ext. 7022
[email protected]
r1concepts is offline   Quote
Old 06-06-2017, 08:45 PM
Thread Starter
  #2
Supporting Vendor
 
r1concepts's Avatar
 
Join Date: Oct 2015
Location: Cerritos, CA
Posts: 572
Bump
__________________
Kevin- Sales Representative
R1 Concepts Inc. - Performance Brake Parts
888-712-6623 ext. 7022
[email protected]
r1concepts is offline   Quote
Reply

Tags
brakes , ebc , hawk , r1concepts , rotors

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off






All times are GMT -5. The time now is 07:55 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.1
User Alert System provided by Advanced User Tagging v3.1.0 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

Jeepģ, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC