Jeep Wrangler Forum banner
  • Hey everyone! Enter your ride HERE to be a part of January's Ride of the Month Challenge!
cylinder

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 22 Results
  1. JK General Discussion
    Ok, I have a cylinder 4 misfire and also sometimes a 2. I did already get the left cylinder head replaced under the warranty but it has come back and they even double checked everything and claim it looks good. It also has coil packs which are less than 6 months old and spark plugs that are now...
  2. JK Technical Discussion
    2016 JKU. 3.6L Pentastar (stock). 6-speed manual. 78.5k miles. Yesterday, the Jeep ran rough through town. Checked the DTCs and it came back as P0303 (3rd cylinder misfire) consistent with the way the engine was behaving. This morning I swabbed the coil plugs of Cyl 1 and Cyl 3 to start the...
  3. TJ Technical Discussion
    I'm looking for a little help diagnosing a clutch issue on my 2003 Jeep Wrangler Rubicon 130k. It's happened to me 3 or 4 times now and I'm looking for recommendations on what to replace first. The problem: After driving on the highway for 15 - 20 min, when slowing down on the exit ramp, my...
  4. TJ Technical Discussion
    Hey all, I’m hoping someone with more knowledge than myself might be able to help me solve this. I’ve owned this 2003 Wrangler for a little less than a year and it has ~80,000 miles on it. It has a 4 cylinder manual transmission and is currently stuck in southern Utah, unable to get above 30...
  5. YJ Technical Discussion
    Hi All, I have a 1992 YJ 2.5L 4-cylinder wrangler, I took the cylinder head off to have it rebuilt and now I want to buy some new cylinder head bolts. I went to O'reilly's today and the guy behind the counter helped me look online for some and found that they have been discontinued. I don't...
  6. YJ General Discussion
    Thanks to YouTube channel oldskool funk, I managed to make a leak down tester out of air compressor fittings. It can be used with a compression tester that uses standard quick connect fittings (I have Harbor Freight 95187). Parts list: A x1 Air pressure regulator - HFT 68223 B x3 Male quick...
  7. TJ Technical Discussion
    I have seen a lot of threads about bleeding the line and replacing, etc.. but I didn't see anything answering my question specifically. I wanted to know how high my reservoir for my clutch master cylinder should be filled. I found conflicting results about the level concerning other vehicles so...
  8. TJ Technical Discussion
    Hi all, I just replaced my clutch pressure plate, clutch disk and throwout bearing after my last throwout bearing seized and blew its ball bearings everywhere. I reassembled everything correctly (I think) but now when I push the clutch pedal in, its very soft. Everything on the interwebs points...
  9. JK Technical Discussion
    Through some help from the forum (ok a lot of help), I have decided to replace the master and slave clutch cylinders to fix a hard shifting problem I am having. The problem is I haven't been able to find any write ups or how to's to on the process of bleeding out the lines and replacing both...
  10. TJ Technical Discussion
    Trying to trouble shoot a (non) starting issue, I took the actuator pin assembly out to inspect and it looks fine (although it could still be the culprit from other posts I've read). My issue is that when I try to put the key/lock cylinder back into the housing, the tang will not pop into the...
  11. YJ Technical Discussion
    Back again with yet ANOTHER problem!! >.< Thats Jeep life I guess lol. Anyway! I couldnt get the jeep to idle without my foot on the gas. new gas filter, seafoamed it, and finally did the venutri system clean. after I did the system clean it instantly sounded a lot better and was way more...
  12. TJ Technical Discussion
    alright heres the story...2006 2.4L started running stupid (sputtering, gargling, backfiring, especially in low RPM ranges), check engine light came on, cylinder misfire. similar thing happened about 5 years ago that was solved by new plug wires. thought maybe they somehow went bad after 60k...
  13. TJ Technical Discussion
    1998 TJ Wrangler - 197,000 Miles - Daily Driver All Stock 4.0 Inline 6 Manual Transmission I just replaced the power steering pump yesterday and drove for at least an hour on my jeep back to my house - so that should have nothing to do with this, but I figured I would mention it. When I...
  14. TJ Technical Discussion
    Ok. Just got done replacing the clutch. I was driving down the road a few days ago and my clutch got hard and then popped. Had it towed back to the shop and began tearing out the tranny. Clutch was in great shape and so was the pressure plate. It pained me to go ahead and replace them. The...
  15. YJ Technical Discussion
    So I woke up one day and the key wouldnt turn/ start my jeep anymore. No matter how much jiggling wiggling and other stuff it wouldnt work. So I swapped out the ignition cylinder and that part is now functioning perfectly. BUT, when I turn the key from the locked position and twist forward in an...
  16. YJ Technical Discussion
    Here's what I have: 90 YJ Saraha with tilt steering wheel Ignition key is pretty worn down (may/may not be an issue) When starting, I have to turn the key hard -- all the way -- to start Sometimes it doesn't want to start, most of the time it does So I'm looking for advice. Do I replace the...
  17. TJ Technical Discussion
    Within the last month "sometimes" when i go to start my jeep its starts but its not right it sound like its not firing in the right order. Sometime if you leave it it will work itself out but most the time im afraid to keep it running. So i stop it and try it again , and agian until it starts...
  18. General Jeep Discussion
    I'm moving our to Utah and thinking about doing more off-roading. I am looking to buy a old TJ Wrangler, but was wondering if there was a significant difference between the 4 and 6 cylinder engines on or off the road.
  19. YJ Technical Discussion
    Hey Everyone, Brand new to the forum, just bought myself a 1990 YJ yesterday. I have been browsing the forum for a few days now and I have found a lot of great info but I cant quite find the answer I'm looking for so here is my question: Can anyone provide me with a quick step by step...
  20. YJ Technical Discussion
    I have a 1995 YJ with the 2.5 4cyl and the 5 speed. It currently has 209,500 on it and it runs great. I know that if you take good care of it the engine will run for a long time, but I just want a "general" answer. -how many miles on your wrangler? -Thanks
1-20 of 22 Results
Top