Search Results for ‘dana 44’

Hello all, I acquired a elocker from a dana 44 out of a JK, I would like to install it into my TJ dana 44. Has anyone done this, I know I have to get axles with 32 splines. Can I just get the correct axles for the TJ 44 with 32 splines or is there additional changes that are required? Regards...

I have a front dana 30 with broken welds, BENT TUBE. I've been searching for a swap. A new dana 30 was 3k. Should I be looking for a dana 44 and hardwire the ELD? Either way, I thought these things were under 2k....yikes

I recently found a cheap ford dana 44 front axle (6 bolt pattern, 67.5" wms to wms) and I'm thinking about swapping it in on my JKU and taking out the dana 30. Does anyone know what kinds of things I would need to do to prepare it and swap it in? It's got everything included but I have very...

Good evening! Ive been having problems finding a Dana 30 3.73 front axle for a reasonable price. The only place that would sell it is Arizona Auto Parts for a whopping 2,700 which seems real steep. I’m still looking for one I’m the Phoenix area or anyone on here that could maybe ship?I’m new to...

Hello everyone, First post in a while. I have a 2007 jku non rubicon and had leaking rear axle seal on the passenger side. Ordered some factory ten axle shafts from north ridge pre press with bearing and seal. Replaced both sides without issues or leaks for the past 500 miles. Note, I changed...

I'm running 35s on a 2016 JKUR, so Dana 44s with 4.56 gears. My load is generally heavy. I'll take it to a scale when the road is open. Looking for recommendations/opinions on axle upgrades.

Need a little help. I have a 2003 jeep wrangler Sahara with a dana 44 limited-slip dif. The only spider gears I can find are for a trac-lok limited slip. Are they the same? I appreciate any help give.

Anybody experience the front drive shaft splines breaking? I went to replace a u-joint and Found this on the shaft. I replaced the shaft and I am noticing a wear pattern that matches the breaking on the new shaft. Front axle shaft on the passenger side of a stock rubicon axle.

I was putting the hard brake lines back on my rear axle (dana 44) and where it has the fitting screws into the driver's side, this happened. The part attached to the axle broke in half. How do I fix this fast? I'm moving in a week and a half and need to drive my 2004 Wrangler.

Fellow Jeep members, I have a couple of questions that I know may have been asked many times. I am however new to the Jeep family and I want your insights with what I want to do with my jeep. First off I have a 1999 TJ 4.0 with a 4in. lift and I have 35s..before I go any further this jeep was...

Hey guys how's it going not really sure how this works this would be my first post just wanna ask which axle route should I go A) I found dana 60 axles both front and rear from a 94 ram 2500 for $300 (some rebuild work may be needed) or B) should I just upgrade my current dana 30/35 axle (not...

I just saw an offer on facebook for a Dana 44 out of a '99 TJ. The axle is completely empty, just the tube and TJ brackets. The guy wants $75 bucks for it... do you guys think this is worth it? Currently running a mostly stock '05 TJ X with the D35 rear. Sitting on 2'' Teraflex springs and...

Brand new crown automotive dana 44 axles, bought for my jeep, but never installed. Sold the jeep. Part #''s 5083666ab , 5083667ab Will separate but prefer to sell as a pair, 5083666ab passenger side 125$ 5083667ab driver's side 150$ Or both for 250$ Fits 2003 to 2006 stock axle housings for...

Hi All, first time on here and looking for assistance, hope someone can help. I have a 2003 TJ TR2 edition with Dana 44 rear axle. A year or so ago I noticed some end float at the rear wheels. Looked about for info and came to conclusion wheel bearings were the issue and went ahead and...

Hello everyone, I am in the market for axle assemblies. I'd like to upgrade the front to a 3" OD and 0.5" wall thickness with 4.56 R&P, ARB locker, and 35-spline axle shafts. I plan to continue running 35" tires as this is my daily driver and any substantial decrease (i.e., 3-4 mpg) in fuel...

I need to get a set of 30-Spline Unit Bearings for my TJ. What are my options as far as brand, so far I've only seen Alloy USA and reviews are not that great for them. I know there is a big debate over why bother with 30 spline axles, but I already have a new axle coming with 30 spline outers...

I have spent the last hour trying to find out EXACTLY what a "Military Inspired" heavy duty front Dana 44 is that FCA puts in the Recons. I have read in WF that it is actually a Dana Ultimate 44, but I can not confirm this anywhere. I have been to Mopar Parts Online, Mopar Performance Parts...

I have a 2007 2 door wrangler x. Currently about to swap out the front dana 30 with the J8 dana 44. I am going to keep the rear wrangler x dana 44 for the time being but will be upgrading that as well. Here is everything I plan to do with the front J8 axle along with the stock rear dana 44. If...

I am going to be swapping out my stock dana 30 front axle. I was going to go with a Rubicon 44 front axle housing but I have heard the J8 44 housing is a lot better. Can I please hear your input on this? What are the differences. Are both of these axles the same width also, I didn't want my...