Jeep Wrangler Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 20 Results
  1. TJ General Discussion
    Hello all, I am looking into building a bumper for my 2002 Wrangler and I want to base it off of the Bestop Highrock 4x4 Bumper I have the bumper roughly laid out in AutoCad and was wondering if anyone had this specific bumper and could provide dimensions. Thanks!
  2. TJ Technical Discussion
    So I've been doing a lot of reading and creeping around doing research and it I can't seem to find any information about swapping the front axle out with a Ford 8.8. I plan on going either 35x13.5r15 or 37x14.5r15 on an '01 Wrangler TJ. Here is a thread listing junkyard front axle swap options...
  3. JK General Discussion
    I wanted to share the custom fabricated spare tire lock my friend and I made for my Jeep... The problem: The BOLT spare tire lock would not work as designed with my ProComp wheels. I did, however, like the idea of having a lock that was made for my Jeep's key. The solution: Fabricate a new...
  4. YJ Build Forum
    I needed some room for my new boom shackles, and the old uhaul hitch was restricting movement. First I was just going to take it off and and put the old bumper back on... than I got a little crazy and decided to fab a new! Removal C-Channel, receiver hitch, bottom bracer First tube 1/8"...
  5. TJ Technical Discussion
    I'm in the process of mounting JK rear shocks to my TJ (I have been warned against it, but I am stubborn and determined at this point, coil springs are opened and shock bushings trimmed). The shocks are much nicer, bigger diameter, in great condition, and red :) However, the compressed length...
  6. TJ General Discussion
    Hey forum! Just made my account. I've had my CPR TJ now for a little over a year and I love that darn thing, even though I've spent about 7 grand on getting it fixed in that year. In short, I have a couple topics I want to bring up in my first post! I hope that's okay with the admins. 1) I...
  7. JK General Discussion
    So about a month ago i threw a rod in my 3.8L motor. Since then its been in the shop in the first attempt to replace the motor. I bought a remanufactured motor from and online seller and had it installed at Tire Pros in stilwater, MN. After about 3 weeks of labor and time wasted waiting for...
  8. YJ Technical Discussion
    Here is what has been going on. I bought the Jeep a few months ago and have been driving it as a daily driver and once in a while I would hear a rattle. I thought it was on the passenger side so this was side I was looking at and thought it was a shock and decided not to worry to much about it...
  9. TJ Technical Discussion
    So I hit some black Ice and did some serious rear corner mangle action. I am going to replace the rear corner w/ https://www.quadratec.com/products/12505_0001%2007.htm The problem I'm having is finding the top corner rail to attach a soft top or just seal my hard top. I was wondering if anybody...
  10. Communications and Electronics
    Thinking about installing a couple subs and an amp under my rear seats of my JKU. anyone done this or have other ideas for sub/speaker placement?
  11. Builders Corner
    custom steel bumpers fab shop *cost is directly related to materials and time of the project other custom trail gear currently building a tanneau cover for the back seat of a 99 wrangler tj located in monroeville PA
  12. YJ Technical Discussion
    (Mods: if this thread is supposed to be in the Fab thread instead of YJ, please move it) I'm designing an aftermarket set of bumpers, both front and rear, for my YJ. I was able to find the front bumper bolt pattern on here, however I can't find the pattern for the rear bumper. What I need is...
  13. Virginia Jeep Forum
    - Mod- Not sure if this is the correct thread to post this in. Please move it if you need to. Thanks. - :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: I am looking to design and fabricate a custom locking bracket for my 2006 Rubicon to mount a HAM, CB, Scanner...
  14. General Jeep Discussion
    - Mod- Not sure if this is the correct thread to post this in. Please move it if you need to. Thanks. - :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: :wavey: I am looking to design and fabricate a custom locking bracket for my...
  15. TJ Build Forum
    So I bought a 2003 Jeep Wrangler Sahara for 10,000.00 after my 2003 TJ was destroyed in an accident. I will be using some of the parts from that jeep in this build thread so I will kick it off with some of the parts I made for that jeep in my Spare time. I am about to end a deployment to...
  16. Pictures Forum
    Jeepers, I was soon hoping to build both front and rear bumpers for my 99' Wrangler. I have several ideas on what I want (including a tire carrier), but the best way to come up with ideas is to see other peoples examples. Post your custom bumper builds! Thanks in advance, can't wait to see your...
  17. General Jeep Discussion
    Created so that all WF members can show off their metal fabrication skills. Whether you built a custom roll cage or just took a sawzall to your bumpers, post your pictures so that everyone can see your handy work. Share some insight, tips, and tricks about anything related to metal work.
  18. TJ General Discussion
    Has anyone ever seen/heard of full side fenders? I think It would look preeetttty neat to have flat fenders running from front to rear and also running boards, all in one. Anyone else think this is a good idea? My buddy and I have been talking about fabricating custom fenders for my Jeep...
  19. CJ General Discussion
    I want to put a Roll Cage on my Jeep and am going to be fabricating my own, and need to know what type of steel tubing to use for the cage. I'm only going to be doing a front roll cage probably. Any other suggestions past the type of steel to use is also appreciated.
1-19 of 20 Results
Top