Jeep Wrangler Forum banner
  • Hey everyone! Enter your ride HERE to be a part of January's Ride of the Month Challenge!
manifold
1-18 of 29 Results
  1. TJ General Discussion
    Exhaust manifold finally cracked Recommendations on what to replace it with? I've seen Banks recommended by some and others recommend OEM. Thoughts? Suggestions? Part #'s appreciated! Thank y'all
  2. TJ Technical Discussion
    Hi, i have a 03 Rubicon that has a really loud tick and sometimes sounds like a knock, it has 150k on the 4.0 and the oil has been changed every 3k miles with synthetic and mopar filter. from my research i have found it could possibly be a cracked exhuast manifold. It is sometimes louder than...
  3. TJ Technical Discussion
    On a 2005 exhaust system (dual manifolds), is there supposed to be a gasket between the cast manifold and the catalysts? The parts I took off didn't have them and the parts I bought didn't come with new ones. I can not find any diagrams that show gaskets at that joint either. The bolts were...
  4. TJ General Discussion
    Took the plunge and bought another Jeep, 2000 Sport 4.0 Automatic, only thing I don’t like about it, but may do a manual swap somewhere in the future. Going to replace the exhaust manifold, cat, and muffler and going to use it as a daily, of course will be in the hills and along the river...
  5. TJ Technical Discussion
    97 Wrangler TJ, 2.5 engine. Since I bought it, it has an issue with the rpm not being stable at idle. When it's cold it is worse and you can hear the engine interrupting. Even when the engine is warm, in 1st gear on Low Gear, if left to crawl at idle it will buck forwards following the rpm...
  6. YJ Technical Discussion
    I've search a bunch on this forum and haven't found much feedback on the longevity of different exhaust manifold options specifically for the 4.0L. My original stock manifold cracked and I replaced it with a Banks TorqueTube header. That one lasted me about 6-1/2 years and 45K miles before I...
  7. YJ Technical Discussion
    So if you're reading this then you're probably doing research on updating your intake manifold. I decided to do the same thing and went with offenhauser brand. What I did not realize and what the sales techs at Summit do not realize is that there is a huge difference between the dual ported...
  8. TJ Technical Discussion
    Alright, so I am a new member to the forum but I have searched this forum for a many things regarding my Jeep. I am new to all the rules so sorry if this answer exists out there, but I have not been able to find exactly what I am looking for. I have a 99 TJ with the 4.0 L I6 and I have a...
  9. TJ Technical Discussion
    I've been working on replacing my oil pan. Which has been completed successfully. Now I'm reinstalling the exhaust pipe (which I had to remove during the install), but that's proving to be the hardest part of this process. Any tips for installing the exhaust pipe to the manifold? I have barely...
  10. TJ Technical Discussion
    I plan to replace my crack manifold in few days. I'm in my drive way and pretty good in mecanic but never done that type of job before. The bolt was there for 16 years. What do you suggest me to help prevent broking nuts in the head. I'm aplying lose nut from the last two days. 1- remove the...
  11. TJ Technical Discussion
    I plan to change my jeep manifold and have never done this job before. So I have a few interrogations. I have done a lot of mechanic in the past but not on exhaust manifold. -First I do not have a torque wrench, do I really need it to do that job or it's optional? I have the spec to tighten the...
  12. TJ Technical Discussion
    Hey all, I'm trying to remove my upper intake manifold off my 2.4L '04. I've got the throttle body, electrical connections and bolts all removed but I can't figure out what is holding the upper to the lower. It won't budge. To follow that up, I'm removing this to get to my valve cover because...
  13. TJ Technical Discussion
    Hello everyone. Apologies if this is somewhere else, I tried searching a few times with no luck. I have a 2001 sahara with the CA CARB compliant emissions system. I have bad cats in the downpipe and have the replacement, but I can't get one of the nuts off. These are the nuts with a welded...
  14. General Jeep Discussion
    I have a ticking sound coming from my jeep wrangled. Someone told me it sounds like my exhaust manifold is leaking. Can this be welded or will I have to get a new one and what does this cost?
  15. TJ Technical Discussion
    hello all, replacing my exhaust manifold/gasket on my 01 TJ SE 4 cylinder. Does anybody recommend a specific replacement brand? I've seen Dorman, ATP, Omix Ada? ANY advice is appreciated. thanks
  16. Maryland Jeep Forum
    Hello all- brand new to the forum and just purchased my first Wrangler, an 01 2.5L. It has a broken bolt/gasket on the exhaust manifold and the service center said it won't pass inspection until I get it fixed. Does anybody have any recommendations on a garage in the Baltimore/Frederick area for...
  17. YJ Technical Discussion
    I have to replace my manifold gasket on my 95 2.5L and might as well replace my swiss cheese exhaust manifold while i have it off. IDK which one to buy. Ill spend the money on the Banks torque tubes ($400) but only if its worth it! I dont want to get an OEM one, i want to upgrade. Any...
  18. TJ Technical Discussion
    So this weekend I found that I had what seemed to be a exhaust leak. Searched around but couldn't find anything on the manifold that could be cracked or loose. Kept driving the Jeep and as I did it got worse as it drove. Last night after work I started the Jeep and i could hear a metal clanging...
1-18 of 29 Results
Top