Jeep Wrangler Forum banner
  • Hey everyone! Enter your ride HERE to be a part of January's Ride of the Month Challenge!
motor

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 25 Results
  1. JK Technical Discussion
    I am trying to figure out what other engines will fit in a 2013 JK. Will an engine from a Dodge Charger, Challenger, Caravan, Durango, etc. fit. They are all 3.6L Pentastar but are they interchangeable. Is there a cross reference that will have that information. Thank you to everyone for the...
  2. JK General Discussion
    Hi Guys, So long story short my wrangler (79k miles) had a oil leak and ran on low oil for a while and now the motor is severely damaged. Took it to a jeep dealership, they said it'll need a full motor replacement. I still owe $9K on it and I'm trying to weigh whether I should just sell it and...
  3. TJ General Discussion
    I think my OEM front wiper motor is about to die, so I picked up a new one from Amazon that had a high rating. Below are pics of the wiring and plug. I'd still like to know what each of the five wires are for on the motor. I know BROWN is ground, and can make educated guesses on the others...
  4. Classifieds Archive
    I have a 2012 JKUR Swaybar/motor for sale (no endlinks). Electronics on actuator went out but can be used to manually wire a switch or be used with the EVONoLimits Manual Rubicon Swaybar Disconnect. There are plenty of write-ups to wire this to a switch or manually disconnect. This is great if...
  5. JK Technical Discussion
    Hey folks, My winch stopped working a few weeks ago. I got around to pulling the bumper today and getting it out for troubleshooting. I cleaned all the connections and reattached. When I hit my remote I get solid clicks from the solenoid but no motor action. When it had stopped working the...
  6. JK Technical Discussion
    75000 miles - just lifted a month ago 4" On 35s" will this 1) void my bumper to bumper warranty ?? 2) be the reason I now have transmission oil leaking terribly from my transmission pan ? 3) be the reason I ran a power train code - p0869 (line pressure high) please someone help before I bring it...
  7. JK General Discussion
    Hate for this to be my first post but I'm in a pickle. Purchased an 08 Rubicon 4 months ago. Heard a ticking noise (value type noise) and then followed by a knocking. Coming from the crank. Took it into the dealership where they diagnosed it as a blown motor. They informed me that this was a...
  8. TJ Technical Discussion
    Hey everyone, I have always read threads on this website but never registered an account till now! (Need some help). I recently sold my 1995 Jeep Wrangler Sahara Edition (she was pretty beat) to upgrade. I found a Wrangler on craigslist from a guy north of Chicago and went to check it out. Real...
  9. Illinois Jeep Forum
    Hey everyone, I have always read threads on this website but never registered an account till now! (Need some help). I recently sold my 1995 Jeep Wrangler Sahara Edition (she was pretty beat) to upgrade. I found a Wrangler on craigslist from a guy north of Chicago and went to check it out. Real...
  10. YJ Technical Discussion
    I blew my 4.0 in my 1991 wrangler. Driving wise (I don't drive it anymore just when it started) it performed fine but just had a loud knocking sound. I assume I am bending one of my pushrods or something along those lines. I was either going to rebuild it or look for another one to swap. What is...
  11. TJ Technical Discussion
    Right after I turned on to the highway over an hour ago a rod shot through the motor, and its scrap now. Thankful I rolled through to the side of the road, and my dad met me with straps to pull my Jeep home. A rod was released, it punctured the motor, through the oil pan. My baby's heart is...
  12. JK General Discussion
    Hello,I am new to this Forum and purchased a 2007 Jeep Wrangler Unlimited about 7 months ago. I bought it "as is" with no warranty after several test drives and a clean carfax report. I had the death wobble within the first week, had to replace clutch assembly within a month, and now need a...
  13. TJ General Discussion
    I just had my jeep lifted 4 inches about a month ago. I have the 1997 SE so i have the 4cyl. Im about to put a slip yoke elimantor and new CV driveshaft from tom woods. But i was wondering about swapping out my rear D35 to a D44. But i also wanted to regear the axle to get the power back. I...
  14. TJ General Discussion
    I rolled my 99 tj sahara and now it wont start! Oil came out of the intake. Idk where to start! It won't even turn over
  15. YJ Technical Discussion
    ok. so i have a 94 yj with a 2.5litre in it. but my buddy just gave me a late 70's running 304 from a cj. i wanna do the old motor swap and get rid of the crappy 4 cylinder, but i wanna do some heavy planning before i start ripping things apart. can anyone tell me what all i need to know before...
  16. General Jeep Discussion
    I just bought a used '97 without diagnosing the engine rattle correctly. My mechanic says I have a bad piston and that engine replacement is the only way to go. Any other suggestions? Will an I6 fit instead of putting an I4 back in? Don't really have the coin to replace the engine right now. 5...
  17. Builders Corner
    Hey everyone, not really about jeeps but i was thinking about a buggy to ride around in. I have some trampoline tubing for the frame, but i was thinking for a motor i'd want a dirtbike motor not sure how to go about it just seeing if you guys have some ideas to bounce off. Basically i'm looking...
  18. CJ Technical Discussion
    I just switched out one a inline 256 4.2 for the same used motor. I have a brand new weber carb. Its a 77 cj 7 quadratrac as my name implies. When I hit the gas at all it almost seems to flood for a minute and not accelerate at all. It will move, shift and drive, but no chance of spinning...
  19. YJ Technical Discussion
    I have had my 95 Wrangler for a month now, (and I love it) it has 140k miles, when I start it up, it is as quiet as a church mouse, but after about 2 or 3 minutes, a pecking noise starts, I cant pin point it....if you rev the engine to about 1000 rpms it stops, I thought it was the exaust...
  20. TJ General Discussion
    I bought it and looked it had a four cyl. but i ran the VIN and it came from the factory with a 6 cyl. any ideas of why? it only has 27,000 miles so its not that, but it did have a snow plow on it, in Buffalo, NY.
1-20 of 25 Results
Top