Jeep Wrangler Forum banner

1 - 20 of 25 Posts

·
Registered
Joined
·
72 Posts
Discussion Starter #1
Hey guys :wave: doesn't seem like there's many people from sask on here. If any people are looking forward to mudding in the pa area in the spring PM me we should set something up and get a few rigs together
 

·
Registered
Joined
·
2 Posts
*Help finding Regs*

Hi guys, born & raised northern saskatchewanian coming back home to roost. Have a '97 Suburban with a 6" list running 37" TRXUS MTs with all the mods to make it souped up, safe & solid. Anyway, I contacted a garage in PA that the family has dealt with for years (so as trustworthy as I'm going to get not personally knowing any) as I am going to need an out of province inspection. When I told them about the lift they all but said it would fail so I am trying to find a copy of the regulations or their inspection parameters or something & not having much luck. I've only found a copy of the "Vehicle Equipment Regulations" from 1987. If anyone can direct me to something more recent I would really appreciate it.

Thanks & hope to see you on the trails soon.
 

·
Registered
Joined
·
62 Posts
Hi guys, born & raised northern saskatchewanian coming back home to roost. Have a '97 Suburban with a 6" list running 37" TRXUS MTs with all the mods to make it souped up, safe & solid. Anyway, I contacted a garage in PA that the family has dealt with for years (so as trustworthy as I'm going to get not personally knowing any) as I am going to need an out of province inspection. When I told them about the lift they all but said it would fail so I am trying to find a copy of the regulations or their inspection parameters or something & not having much luck. I've only found a copy of the "Vehicle Equipment Regulations" from 1987. If anyone can direct me to something more recent I would really appreciate it.

Thanks & hope to see you on the trails soon.
There are regulations regarding bumper and light heights. Take a look at this doc for an example.
Http://Reginapolice.ca/vehicle/vehicle_modifications.pdf
 

·
Registered
Joined
·
2 Posts
Thank you Candyman8019.

I had found the Regina Police document & the google search you mentioned is where I found the regulations from 1987. I'm just worried that there were some changes when there was all the talk about changes 3 or 4 years ago.
 

·
Registered
Joined
·
1,078 Posts
Regina here too. There is an INSANE amount of jeeps on the road in this city. Surprised there isn't more Regina representation on this board.
Ya I represent Regina. I have been bouncing around these last few years but Regina is still my home and I should be moving there in September again for many years. Anyone in kenosee area? I'm there this summer working at a camp in the park
 

·
Registered
Joined
·
32 Posts
I'm in Regina too.

There doesn't seem to be a good place to off-road here. Or a good install shop.

And how come nobody does the Jeep wave?

There are tons of Jeeps here...
 

·
Registered
Joined
·
3 Posts
I am from the Kenosee area. And I will look into the regulations I work at a safety inspection station. I am not on here often but I will try and remember, Myself and a couple co-workers usually sneak through the local park to see how deep we can go and we got around the height rules by finding jeeps with Sk plates because a safety isn't required for day passes :p
 

·
Registered
Joined
·
3 Posts
I looked up bumper and light heights. Let me know if I should sticky the info. Any other questions let me know.

All measurements are to a level ground surface.

Bumpers:
Height must be between 15" - 22" at the middle of the bumper.
Width has to be a minimum of frame rail to frame rail for the solid portion.
Note: Do not weld bumpers to frames, any welds to frame are auto fail. Gr. 8 bolts are the way to go.

Lights:
Headlamps are to be 22" - 54" measured to center of the headlamp.
Tail lamps are to be 15" - 72" measured to center of the lights.
 

·
Registered
Joined
·
9 Posts
Hey everyone, just thought I would check in from Regina. Just wanted to let anyone that may be interested know that I am starting a side project plasti dipping rims, emblems, grills, etc. if your interested PM me and maybe we can work something out.
 
1 - 20 of 25 Posts
Top