Installing a Backup camera with the Mopar RBZ 430 Radio

Ticommando · Jul 11, 2019

Hello, I want to install a backup camera in my jeep. I have a JKU 2013 with the RBZ 430 radio. This is the radio that has NO navigation (See Picture attached). I want to know if someone has successfully been able to display the camera in this radio? I know the radio needs to be flashed to enable the camera option but I am not even sure if this radio model will support a camera. I ordered a OBD2 Scanner and JSCAN application to get the camera option enabled.

I am particularly interested in the Alpine Camera HCE-TCAM-WRA. Alpine says that the camera is compatible with ANY jeep starting 2007 models. I am willing to go with other cameras if this Alpine is not an option.

Basically my question is, has any of you been able to display a camera in the Mopar RBZ 430 Panel?

Many Thanks,

Jk4papa · Jul 11, 2019

Yes, look at the JScan application. You will also need a Bluetooth adopter.

Sent from my ONEPLUS A6013 using Tapatalk

Thaiwoo · Jul 11, 2019

On Amazon.com there is the following review

The installation was pretty straight forward, but I would add that you need the camera harness adapter Alpine Electronics ALP-HRN-CAMCH Camera Input Harness for the HCE-TCAM1-WRA, Rear View Camera System & 2007-2017 Jeep Wrangler Factory Display if you wish to use with the stock touch screen stereo. I have the non-nav stereo 430 and it works fine.

j_foust · Jul 12, 2019

Amazon delivered the alpine harness, obd adapter for Jscan, and a camera today. I’ll be putting this set up on this weekend. Maybe the best $50 mod

*chris* · Jul 12, 2019

What camera did you buy?

Chris

jeep63 · Jul 12, 2019

Good luck. I think you will be fine. I do not believe navigation is the key here, I think it is the 430 model itself. It is an easy and affordable mod for sure.

cbrown06 · Jul 20, 2019

Can anyone advise where and what color is the backup light wire on my 2012 jk manual trans that I need to tap into?

Sent from my iPhone using Tapatalk

3oomer · Jul 20, 2019

White/Grey

cbrown06 · Jul 20, 2019

Thanks. Where do I tap into it? At the rear of the Jeep? Or near the head unit?

Sent from my iPhone using Tapatalk

Jk4papa · Jul 20, 2019

I tapped into it at the rear of the Jeep by the right hand tail light.

Sent from my ONEPLUS A6013 using Tapatalk

cbrown06 · Jul 21, 2019

Thanks again

Sent from my iPhone using Tapatalk

moparpeetie · Jul 16, 2020

I know this thread is old but... I bought the Alpine harness and a similar camera to the one in the link. I have a RBZ430 that is not original to my wife's 2017 jku but it works just fine. I have Alfa OBD and I turned on the back up camera. I get the screen that says "check your surroundings" but No video from the camera. I have no way to test the video feed. (No laptop or monitor) Not exactly sure what is going on or NOT going on????? HELP!!! PLEASE!!!!

cbrown06 · Jul 16, 2020

Problem with the camera. If it’s the amazon camera, occasionally they arrive defective. Double check your connections too

Sent from my iPhone using Tapatalk

moparpeetie · Jul 16, 2020

I finally figured it out after buying a second camera that I didn't need.
It was a bad ground to the camera, works flawlessly now!!
Thanks for the response, much appreciated!

Installing a Backup camera with the Mopar RBZ 430 Radio

Attachments

Our Vendors

Top Contributors this Month

Recommended Communities